HTS22GBPC General Electric Refrigerator - Instructions

I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.

Gaskets designed to just press a flange into channel around doors. I tried everything..I pre-heated gaskets ; I put dish soap around flange; I used (carefully) a heat gun as I pressed gasket in. Really very difficult to get the gasket to seat fully. I don't know if there is a tool to help you do this, but you need strong fingers/thumbs and endurance. Once seated, you will need to heat the gasket to get it to fully seal against the fridge. Just lightly heat along the gasket with the doors closed and press open the fold with your fingers. I let the doors stay closed over night. Works great now, but I probably will call a repairman the next time. I miss the old gaskets with a zillion screws..PITA, but easier.

I removed the pan with the gliders attached. I used a socket set to remove the broken glider from the pan. Then, I put the new glider on and tightened the socket and put the whole apparatus back in the refrigerator. I am a 75 year old woman and had no trouble doing this myself.

1- youtubed the potential diagnoses, 2- resourced and ordered parts, 3- removed old socket, installed new one :-)... My fridge is an older fridge and could've used a screwdriver for eyeglasses. Plug and play easy... YAY!

On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.

While only 4 yrs old, an annoying sliding vegetable drawer would tilt to one side and NOT close well at all. After seeing the parts so easily on Parts Select...I had it fixed in under 7 minutes and it is as good as new....you can slide it without frustration

So easy - unscrewed old screws, replaced part, put screws back in!

The hubby couldn't believe that I finished as quickly as I did...

removed two screws which let me take the old part off. I then put the new part on.

Shipping was extremely fast.

I removed the drawers, then removed the two screws that held the drawer slide in place. I replaced the drawer slide, secured with two screws, and then replaced the drawers.

Un Plugged the frig. Unlocked the socket by pressing down on the latch. Pulled the socket out ensuring I had enough slack. Unplugged the old socket installed the new. Plugged the frig back in. Tested the switch . Very easy-to-use.

pluged the wire harness into the new socket from the back and snaped the socket in place.

Remove the drawer and the shelf glass assembly. using a #2 phillips screwdriver remove the two screws that hold the drawer slide rail. Discard the old slide and place the new slide in position and install the two screws. Be careful not to over-tighten the screws. Place the drawer back on the slide and close it. Next place the front of the glass shelf under the lip on the front of the slide rail and set it in place. Job Complete!

Part received quickly and was a very good deal!

The broken slide rail mounting was held with 2 screws. I removed the plastic shelf on the top and unscrewed the broken part. I replaced it with the new slide rail part and screwed in the 2 screws. I replaced the slide drawer and the top shelf and the job was done...... very easy! Very satisfied!

First I removed the glass shelf on top of the drawer. I then removed the drawer and unscrewed the old drawer rail. After this I cleaned everything, screwed in the new drawer rail, reinstalled glass and drawer and I was finished.

The plastic slide rail that held up the bottom shelf of my frig as well as the top drawer had cracked & eventually broke. Being a widow who lives alone, I knew I could call my son to fix my frig - but I thought, maybe I could do this myself. I found the Brand, Model # & info I needed right on the inside of my frig. I did an internet search for Refrigerator parts, another first for me, found this web-site, then a diagram of my frig, I selected a part & ordered it. When it came in, I had ordered the slide for the bottom drawer & I needed the slide for the top drawer. I called the # from the invoice & got the nicest lady who found the correct part #, ordered it, then proceeded to process the return of the incorrect part I had ordered. The correct part came 2 days later & my credit card was immediately credited after they received the part I sent back. I was so excited to complete the "repair" myself, then with great pride I got my screw driver and changed out 2 screws - "completing my first repair job, all by myself". I diagnosed the problem, ordered the part & completed the repair without help from my family. I was very glad to add this web site to my Favorites. A great big ThankYou to Parts Select !!! Ann Payne