TFCW22RRAWH General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Martin from Yakima, WA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
door was not closing properly
watched the video on changing the cam and then did the repair as per the instructions. the job was easy and now the door works as it should. that saved me lots of money by doing it myself. thanks, Martin.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Baytown, TX
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Plastic cams had worn out
Took the hinge of the top and lifted door of the bottom. Replaced cams and reinstalled
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from Corpus Christi, TX
- Parts Used:
- WR49X10183
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Rust in ice
Replaced auger and front helix kit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Reno, NV
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Refrigerator door would not close completely.
1. Watched the video on how to make the repair. 2. Used the tools recommended. 3. Followed easy instructions as demonstrated on video, and Viola! It was repaired.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Susan from Chevy Chase, MD
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Refrigerator door didn't close without a big push.
Took door off. Replaced two cams at bottom of door, referencing those on the bottom of the freezer door. Also followed a video on the net. Worked like a jewel!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol J from Alexandria, KY
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Door would not close properly at the last few inches, now it closes good at this time but now need to be raised up to the 5/8 inch as the book says, haven't done that yet
the door closing cam works fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jim from Wheaton, IL
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Door didn't shut cleaning, by itself
I watched the video online, and said, "hey, I can do that." And yep, I did. I'm pretty comfortable with handyman work - but had never tackled a frig door before. The door closing cam that had completely come apart turned out to be straight forward to fix with the replacement part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Windham, NH
- Parts Used:
- WR17X2760
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
rust in the ice
there was rust inbedded in the ice cube. replaced the front plate in the ice maker bin. If you can't remember what parts you remover, take pictures of the replacement
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Joliet, IL
- Parts Used:
- WR62X23154
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Ice maker- wouldn't release cubes only crushed ice.
Really easy- turned off ice maker, powered down appliance briefly. Removed ice maker by removing 3 screws with 1/4 nut driver. Unplugged ice maker from power supply. Removed and replaced solenoid arm assembly. Reversed steps and whammy - ice cubes dropped.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- GENE from ASHEBORO, NC
- Parts Used:
- WR62X23154, WR62X26536, WR62X26536
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
No cube ice. We had crushed ice.
Removed ice select control unite from freezer by removing 3 nut screws holding unite in place. Disconnect 2 electrial plug ins.Remove unite from freezer and place on table for easy work space. Remove 4 nut screws holding Solenoid & Arm. Replace with new Solenoid & Arm. Reinstall back in freezer and now we have cube ice again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Spring, TX
- Parts Used:
- WR62X23154
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator was only dispensing crush ice and not cubes
Solenoid pushing the crushed ice flapper was burned out. Solenoid was easy to find unplug and replace. I used the old piston which simplified things. Now works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from Flowood, MS
- Parts Used:
- WR71X10715
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed an extra shelf
Part was received quickly and quickly installed-Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PETE from LAKE FOREST PARK, WA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door would not close on first touch.
I ordered a door closing cam (4320595) to start with and then relized I needed Bottom Hinge Assembly which I ordered#4326874. I had no problem installing. I have returned for credit the door closing cam. I HAD NO TROUBLE INSTALLING THE BOTTOM HINGE ASSEMBLY. ONLY TOOK 10 OR 15 MINUTES. I am a retired building contactor and hade all the toos necessary.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from yorkville, IL
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Door cam broke
Followed the instruction video. The price was high for a plastic part the size of a quarter.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Anaheim, CA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Wrench set
broken cam riser on the bottom of the door
I ordered a cam riser for the refrigerator door. I watched the "how to" video the day I ordered the part. It took about a week to get the part, but I was ready when it arrived. The 'how to' video was a big help. It showed me how to take off the door and replace the part. The process was quite simple! Oh! Don't forget to turn the refrigerator on again!
Was this instruction helpful to you?
Thank you for voting!