GTS18EBRW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mackenzie from Williston, ND
- Parts Used:
- WR09X20002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Compressor would randomly not turn on. Fridge too warm sometimes.
Replace temperature control. That fixed it. Also, removed plastic bag obstructing air vent in freezer which added performance. Fridge works good now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from NAPLES, FL
- Parts Used:
- WR24X10228
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Replace the door gasket on the freezer door of my top-freezer refrigerator
Removed the door by removing the two screws holding it on. Do not try to do this repair with the door attached. Easily removed the old gasket. Getting the new one on the door was EXTREMELY difficult. I couldn't do it. After 90 minutes, I gave up and called my appliance repairman. When he arrived, he and I worked together to get the new gasket on the door. It took 2 sets of hands to do this. It still took us about 40 minutes. My repairman had a few choice words about the design of the system holding the gasket on the door. Ditto for me. So the cost of my repair was doubled because I had to pay the repairman to help me attach the new gasket. I should have just bought a new fridge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eileen from Coto de Caza, CA
- Parts Used:
- WR23X37285
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
switchlight on my refrigerator was not working
I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steve from Ridgecrest, CA
- Parts Used:
- WR60X31522, WR02X12008, WR60X46086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Freezer was not freezing food.
Inspected freezer because food was not freezing, getting cold, but not freezing. Noticed fan was not blowing air, but making a little motor noise, like it's trying to turn. Removed cover panel, and found the fan blade rubbing on the panel, fan shaft was worn out and very loose, wobley. That told me the fan needed to be replaced. Found part on the GE Partselect website and ordered the parts via the website order process. This was easy. The parts were shipped quickley and were at my front door the next day. Couldn't believe it. The actual process was very easy: Remove cover, remove bracket holding fan motor, remove and replace motor, re-assemble parts. About 20-25 minutes from start to finish. Freezer is working like it's suppose to.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Boyd from Blaine, WA
- Parts Used:
- WR09X20002
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Could not adjust temperature
Replaced temp controller
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Henry from DOUGLASVILLE, GA
- Parts Used:
- WR09X20002
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Fridge never cuts off.freeze everything inside of fridge.
To remove the temp sensor.2 Phillip head screws not remove the cover inside fridge .the temp control knob cover.removed that and unplugged switch.installed new switch.reinstalled cover.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ken from fulshear, TX
- Parts Used:
- WR09X10106
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
During Hurricane Ike, frig. saw several inched of saltwater and sand underneath. AFter cleaning up, I tried to run and only the blower fan worked. It must have been just above the water. The compressor did not kick on. I looked at the lowest elec. connections and saw corrsion on the overload protect
This was after sitting idle for 9 mos. I simply pulled the part, ordered the same part and installed. Nothing more than a couple of screws and 2 wire connections. It now works great.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kimberly A from Columbus, OH
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
end cap to bar of freezer door broke
Snapped end cap onto bar and installed bar onto freezer door.
I considered going to an appliance parts store but found the part very easily on the internet and had it within 2 days. I am very busy which was very helpful.
I considered going to an appliance parts store but found the part very easily on the internet and had it within 2 days. I am very busy which was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary from New Milford, NJ
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cap on the door retainer bar broke.
The replacement cap fit perfectly. Unfortunately when the orinigal cap broke it tookout a small piece of the surrounding plastic leaving nothing for the new cap to catch. I have the piece and tried several kinds of glue but nothing holds it securely enough. I would however readily recommend your company. The service was terrific.
Thank you.
Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kaye from San Francisco, CA
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I didn't know if I could get a replacement part, but I googled "replacement parts" (or some such), and since this website looked easy to navigate, chose it. (Actually, I did my ordering via telephone). The sales rep. helped me clarify which part I needed, I ordered it, and received the part the very
I simply snapped the two end pieces into place, attaching the guard rail. It was like putting the pieces of a very easy puzzle together‚ especially for someone like myself who is mechanically challenged.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Travis from North Quincy, MA
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old end cap broke.
Put the new end cap on and snapped it into place, took about 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Northglenn, CO
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The above door End Cap broke.
The repair just required snapping the new part on to the door shelf and then snapping the shelf in to the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruchik from Bronx, NY
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken shelf retainer bar end cap.
I ordered 2 end caps just to keep one as spare. Turned out I had ordered a size larger than the one already on the refrigerator. So I replaced both ends and it worked fine - with increased shelf space. Now I can even fit a gallon container with ease!!! Took about 20 seconds. I just wish there was an easier way to measure parts before ordering. Otherwise, the entire process from order to finish took about 3 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from FLUSHING, NY
- Parts Used:
- WR60X10168
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
The freezer just cool but could not freeze the water and the front of door is quite hot to touch.
First I observe that the compressor motor is running since the freezer is cooling. The purchase of the condenser fan is initiated and when the part arrive it is just easy to reinstall the replacement condenser fan.
The problem on the front of the freezer door remains hot to touch and the compressor runs for a while and stop. The freezer is cold but still could not freeze the water. Inspection of the condenser fan reveals that it is not running. The order for the condenser fan from PARTSELECT came in a few days. Cleaning of the condenser of lint was first done and the process of removing the defective fan is just easy so with the installation.
The refrigerator as of now is running in perfect condition!
The problem on the front of the freezer door remains hot to touch and the compressor runs for a while and stop. The freezer is cold but still could not freeze the water. Inspection of the condenser fan reveals that it is not running. The order for the condenser fan from PARTSELECT came in a few days. Cleaning of the condenser of lint was first done and the process of removing the defective fan is just easy so with the installation.
The refrigerator as of now is running in perfect condition!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marcella from SPRINGFIELD, MA
- Parts Used:
- WR17X11662
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Shelf was cracked on both sides
I first washed old shelf to make sure glass will easily slip out. Installed old glass and replaced.
Was this instruction helpful to you?
Thank you for voting!