90290KD General Electric Refrigerator - Instructions

Simply take off the back panel. Remove the old run capacitor which is attached to the compressor by a white part. It pulls right off. You will have to unplug two wires. I took a pic to ensure I plugged the wires back up the correct way. Then I attached the new capacitor to the white part and put on the sleeve that was included, plugged it back into the compressor and zip tied the excess part of the sleeve. Once done plug fridge back up (always unplug electric devices when doing maintenance) to check before replacing back panel. It may take a few minutes before it kicks on.

you must pay careful attention when taking the dispenser apart,especially the long rod that controls the deflector,but if close attention is payed to disassembly you should have no problem.

Removed 2 screws that hold it on, put the new one in with the 2 screws that were removed.

I layed several small 2x4 blocks on the floor, then raised the door up from the hinge, using the small pry bar. Then removed the the screws for the hinge. Removed the screws holding the door stop and removed the door cam. Then, I replaced the door closing cam. Replaced the hinge and screws. I Lowered the door on to the hinge and applied a little lubricant to the cam and job complete.

I was so pleased to find your website. We have just one company here in Columbia,S.C. that sells refrigerator parts. I did find out that they wanted about $60.00 for both pieces. Needless to say,I was just going to do without. I knew there had to be someone else. I found you guys on line,ordered my parts for a little over $5.00 a piece,and I put them in myself. I'm talking standard GE parts,not knockoffs. I am so pleased. Thanks for being there. I tell everyone about you.

I emptied everything from door compartments.I removed the top cover of the door pivot with a phillips screwdriver. I removed the two screws that that hold the pivot bracket with a 8 mm socket. Lift the door off the bottom pivot bracket. Remove the old bottom pivot bracket with an 8mm socket and replace it with the new cam bushings.You must replace both bushings on the bottom of the door and on the bracket that mounts to the base of the body of the refrigerator. Reinstall the door and screws .The doors should be level with each other if they are installed properly.If not check the freezer door .The bushings may be worn on that door also.

I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.

removed broken bin , slid new ice bin in closed door. I bought the complete part.

Unplug refridge then loosened two bolts holding old ice maker. Lower then unplug and removed. Plugged in new harness and tightened two bolts to secure new ice maker. Plug in frig and wait for ice.

I ended up needing to order a new ice maker because the one I had is discontinued. I'm a 65yr old grandma and I did it myself!!!! The hardest part was finding the tool to loosed the nuts. I took the old one out and just put the new one right in it's place. Easy as pie.

I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.

Propped the door up with wood so we could change it without removing the whole door.
Removed &Replaced the cam and bracket quite easily. It did require 2 people, one to help hold the door while the other did the work.

The PartSelect web site was able to direct me right to my GE double door frig using the model number. I called in to order the parts that were worn out with some operator assistance finding out all parts were available to my surprise. I received the parts in just a few days. I blocked the door up with some scrap lumber allowing me to take the old hinge off being careful to watch where the old parts were located. I reassembled the new hinge. It all took about 30 minutes and about $40. If I would have called a service repairman it would have easily cost me $100 and with a lot less satisfaction. This is the second time I have used PartSelect with similar results.

First, I removed all items on the door shelves and the shelves themselves to reduce the weight of the door. The door came off by itself because the bottom hinge had broken. Then I placed the door horizontal on the kitchen floor to have easier access to the bottom of the door. I had a piece of blanket under the door to prevent any scratch. I then removed two screws holding the door closing cam and shim and replaced them with the new parts. Next, I removed the base grill to have easy access to the old hinge assembly on the refrigerator itself. All I had to do was grab it firmly at either end and pull it forward. I replaced the hinge assembly with the new one. I removed the cover on the top hinge assembly and removed the two screws that secured that hinge (I was not able to put the door back without removing the top hinge assembly). All down hill from this point. Time to reinstall the door, aligning the bottom of the door cam over the hinge assembly and setting the door down on it making sure the door sets on the hinge assembly cams. To the top of the refrigerator. reinstalled the top door hinge assembly and cover (I had to make sure the door was standing straight vertically before I tightened the nuts), I also put a small amount of white grease into both the top and bottom hinges.

I took the ice maker tray out and dumped the ice and then removed 4 screws to take the plastic front off the drawer. I then took 4 more screws out to remove auger assembly. I could now unscrew the broken nut and replace it with the new one and put the snap ring and washer back in place and then put everything back together. Done
Had I had my lathe running at the time I would have made this part out of aluminum instead of the new one and original that is out of plastic which is why it did not last.