TFG25PRBCWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Robert from Rockford, IL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
heavy frost buildup in ice dispenser chute and door
After inspection of the new door recess assembly, I realized that I could use sidecutters (electronic assembly type) and 'clip' off the inward lock tabs of the old recess assembly and disengage it from the crank door arm without any further disassembly of the refrigerator door. It was easy to 'unhitch' the tang from the crank arm and wiggle it out through the external opening of the ice/water dispenser compartment. I reversed the process and inserted the new assembly through the external opening of the compartment. The new door recess assembly snapped into place on the crank arm and fit tightly against the ice chute opening, correcting the issue caused by aging distortion of the old rubber seal cup portion of the door recess assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from Genoa City, WI
- Parts Used:
- WR17X4358
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The dispenser water reservoir had a pin hole leak.
1. Turned off the water supply to the refrigerator.
2. Removed the front panel and disconnected the water line to the front left.
3. Removed the left rear (freezer side) panel and disconnected the reservoir from the main water supply input. This was a little tricky to figure out. You must push in the water line at the same time pushing in the coupling. Then pull the line out while keeping the coupling pressed in.
4. Removed the screw that holds the reservoir to the back of the refrigerator.
5. Pulled the old reservoir out and replaced it with the new one.
6. Basically the rest is the reverse of the above. It took a little bit to fish the lines through the original path they came.
Overall this was an easy repair. If I had known how the coupling in step 3 worked this would have been a 15-minute project.
2. Removed the front panel and disconnected the water line to the front left.
3. Removed the left rear (freezer side) panel and disconnected the reservoir from the main water supply input. This was a little tricky to figure out. You must push in the water line at the same time pushing in the coupling. Then pull the line out while keeping the coupling pressed in.
4. Removed the screw that holds the reservoir to the back of the refrigerator.
5. Pulled the old reservoir out and replaced it with the new one.
6. Basically the rest is the reverse of the above. It took a little bit to fish the lines through the original path they came.
Overall this was an easy repair. If I had known how the coupling in step 3 worked this would have been a 15-minute project.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kyoko from Bellevue, WA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
frost/ice buildup in icemaker chute in the freezer door
The only difficult part was not knowing which parts had to be removed to gain access to the flapper to replace it. It appeared as if the frame around the control panel would have to be removed as well as the door handle; we tried but were not able to remove the frame. It turned out that the panel just popped out with the frame in place. Once we had access to the flapper, it was easy to replace it. The repair fixed the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Travis from Hillsboro, OR
- Parts Used:
- WR17X3489
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light Shield Broke Off
The light shield is only held in with a single screw, so it was the simplest install ever - unscrew the old light shield (in my case, the remaining piece of the light shield), put the new shield in place, and screw it down. Doesn't get any easier than that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Indianapolis, IN
- Parts Used:
- WR17X4153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grill was tarnished and flaking.
Grill for the water dispenser in the door. All I had to do was drop the new one in place.
Received the new grill in one day after ordering.
Received the new grill in one day after ordering.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Union, NJ
- Parts Used:
- WR17X3489
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The freezer light shield was broken.
I removed the ice maker,removed the broken piece of the old light shield,screwed the new light shield in place,and replaced the ice maker.It took all of 5 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Colleyville, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No water through door dispenser
Replaced flapper valve per website instructions. GE factory technician took two weeks to get here, charged over $100 for the call and told us we needed a new refrigerator door at a cost of over $500 to fix the problem. We sent him packing. After visiting the PartSelect website, the $5.88 PartSelect flapper valve fixed the problem. Amazing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maxine from Glen St. Mary, FL
- Parts Used:
- WR12X10152, WR12X10123, WR12X10782
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Handles Turned A Ugly Yellow
I just popped the upper and lower tail handle off, unscrewed the door handle, then I screwed in the new door handle and popped the upper and lower tail handle back on. Easy as pie because I was concerned since I am a female.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Anaheim, CA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The icemaker quit making ice and the water started forming on the bottom of the ice bucket.
First I removed the electrical plug from the back of the freezer that plugs into the icemaker. I then removed the two hex head screws that hold the icemaker to the wall of the freezer and removed the icemaker. I removed the plastic cover, which incidentally protects the gears, by prying it off with a srewdriver. I removed three small nuts(7mm) which holds the internal cam in place. I removed the cam by pulling it off the shaft. Once I got the part from you folks I reversed the procedure that I just mentioned, and put the icemaker back together. It works great. The part with shipping was around $16.00. A new icemaker was roughly $159.00. If I would have called a technician it would have cost around $300.00 to repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Wyckoff, NJ
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Ice maker stopped making ice
I had made a dry run at the repair after watching the instructional film provided by part select and it seemed easy enough.
The only problem was that i needed to use the electrical cord extender (provided) to adapt to my plug type. That presented a problm because it needed to be tucked up out of the way to allow the ice bin to clear. Just needed to be creative in how you wrapped the cord behind the ice maker unit before snugging the attachment screws.
Cranking out ice like crazy.
The only problem was that i needed to use the electrical cord extender (provided) to adapt to my plug type. That presented a problm because it needed to be tucked up out of the way to allow the ice bin to clear. Just needed to be creative in how you wrapped the cord behind the ice maker unit before snugging the attachment screws.
Cranking out ice like crazy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from BRICK, NJ
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My ice container and Ice chute were freezing up and getting blocked, and my filtered water line was also freezing
I just followed the instructions on the video and it was exactly as they said......no surprises.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from FIFE LAKE, MI
- Parts Used:
- WR30X256
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Plastic guide in rear of bucket broke it guides auger when dispensing ice
I simply removed 6 screws that held bucket to face and pit on new bucket and put it back in freezer works great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip M. from SIMPSONVILLE, SC
- Parts Used:
- WR32X1461
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
GE vegetable drawer broken.
Concerned about removing and attaching front panel to broken drawer. Rep. said wasn't sure but most just snapped together. Rep. was correct. No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George V. from PITTSBURGH, PA
- Parts Used:
- WR17X3489
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Freezer Light Shield Cracked at mid fastening point
replaced the broken one with the new part
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bruno from ROME, NY
- Parts Used:
- WR12X10152, WR12X10123
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Old and yellow handles
Just take out the old ones, and clip in the new ones
Was this instruction helpful to you?
Thank you for voting!