TFK22PRXAAA General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- William from Washington, NJ
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Fridge door did no close and was out of alignment
Followed previous poster's steps. Replacement of door closing cams took 35 minutes. Make sure you buy 2 cams for each door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Burmingham, AL
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Problem closing door, would not shut easily.
My wife and I gave an old, but really good refergerator to our son (a Major in the Army). Upon taking it into his house he had to remove the doors of the refergerator. While he put the doors he lost the "cam" for the door, making if difficult to close (actually had to lift the door up and then close it). I ordered the replacement part, and unless I am mistaken, it arrived the same day. I still cannot figure out how this happened, but it was great!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- DAVID from NEWPORT, PA
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Door would hang up half way closed
Replaced both upper and lower cam's. Removed door from refrigerator, removed bolts on door cam on bottom of main door and replaced cam, then removed bolts from door hinge assembly, drilled out rivet holding on cam, replaced with new cam and re-riveted.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Darien, IL
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Door won't close
This my second time to do it after 8 years. Took 10 minutes.
1 Remove all the contents on the side door
2 Remove the 2 bolts on top connecting the door to the refrigarator
3 Lift and remove the door up and put it the side
4 Clean and remove the old door closing cam put the new one
5 Door ref is fixed
1 Remove all the contents on the side door
2 Remove the 2 bolts on top connecting the door to the refrigarator
3 Lift and remove the door up and put it the side
4 Clean and remove the old door closing cam put the new one
5 Door ref is fixed
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Upper Malboro, MD
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Door would not shut by itself.
I followed the directions on the computer and everything went just as the video said it would. This was one of the easiest repairs I have ever done. Usually, it does not go as planned.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Neal from Cleburne, TX
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Door would not close properly
Removed the door and loosened the bottom bracket and scraped the old cam off. Mounted new cam and tightned the bracket. Replaced door and it was a total sucess.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Grand Blanc, MI
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Door closing cam worn out
Removed refrigerator door and replaced bottom door pivot with the included mating cam and the door closing cam on the bottom of the door.
I didn't know that there were two mating cams and only ordered the door closing cam which I read online was the problem. It was the number one part on the part select list. The number two part was a kit including the door closing cam and the pivot with mating cam attached. It would have been helpful if there had been some notes that said check condition of both cams before ordering the part. So I have a spare door closing cam and paid an extra $19 including $8 shipping which negated a return.
The repair is easy - getting the right parts the first time is the trick.
I didn't know that there were two mating cams and only ordered the door closing cam which I read online was the problem. It was the number one part on the part select list. The number two part was a kit including the door closing cam and the pivot with mating cam attached. It would have been helpful if there had been some notes that said check condition of both cams before ordering the part. So I have a spare door closing cam and paid an extra $19 including $8 shipping which negated a return.
The repair is easy - getting the right parts the first time is the trick.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ron from San Antonio, TX
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Door would not stay open
Removed the top cover using a Phillips screw driver to access the top 2 screws holding the bracket. Once the bracket was removed, lifted the door off the bottom hinge. Replaced the door closing cam, replaced shims and screws. Placed the door back on the bottom hinge, inserted the top bracket and secured.
This was the ultimate resolution to the problem. The problem I encountered was getting all of the correct parts. It took me 3 tries to finally identify and receive the parts needed to make the repairs. Using Part Select made it easy because they had the parts I needed. My 3 tries were partly my error and does not reflect on Part Select. I would recommend others use Part Select when choosing their replacement parts.
This was the ultimate resolution to the problem. The problem I encountered was getting all of the correct parts. It took me 3 tries to finally identify and receive the parts needed to make the repairs. Using Part Select made it easy because they had the parts I needed. My 3 tries were partly my error and does not reflect on Part Select. I would recommend others use Part Select when choosing their replacement parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Chesterfield, MI
- Parts Used:
- WR2X4901
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Refrigerator door would not close by itself - would stay open when you thought it was closed
1st: Order (2) closing cams! One for the hinge pin / bracket and one for the bottom of the door.
The closing cam on the door was where the Dremel type tool is required, since you have to grind the head off of a factory rivet.
I installed the cam with an aluminum pop rivet.
Next, remove the bracket on the bottom of the door with sockets and install the second closing cam.
Re-attach the top door hinge pin and align visually; tighen all bolts. Job finished, but more important , my wife is not nagging me about the repair that I put off for over a year!!!!
The closing cam on the door was where the Dremel type tool is required, since you have to grind the head off of a factory rivet.
I installed the cam with an aluminum pop rivet.
Next, remove the bracket on the bottom of the door with sockets and install the second closing cam.
Re-attach the top door hinge pin and align visually; tighen all bolts. Job finished, but more important , my wife is not nagging me about the repair that I put off for over a year!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Arlington Heights, IL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost on the bottom of the ice bin frome warped rubber flapper
Pulled the outter cover off, removed the electronic board, replaced the flapper and put it back together again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES R. from INDIAN SHORES, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Moisture seeping into freezer through ice dispenser
Removed ice dispenser trim from bottom-up and then removed control panel by gently pulling up from the bottom. Removed four screws holding dispenser chute and then two screws holing flapper assembly. Replaced gnarly old flapper with a new one and put all removed pieces back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from zion grove, PA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
rubbeer flapper was worped causing frost in the freeze
The same as the vidio, very easy. Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- HERBERT from Harlingen, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
gasket was shot
took off the panel, took out 4 screwws, took out old flap, installed new flap, put screws back in , and put trim back on.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- vincent from mahwah, NJ
- Parts Used:
- WR2X4901
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
door was not closing properly
Your vidio was Brilliant !!i just followed your instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Atlanta, GA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost was building up inside the freezer just above the ice dispenser shute.
Followed the instructions and replaced the door recess.
Was this instruction helpful to you?
Thank you for voting!