TBX21IIBRRCC General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Matthew J from White Plains, NY
- Parts Used:
- WR30X10093
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Wrench (Adjustable), Wrench set
Broken ice maker replacement
Installing the actual ice maker was quite easy. What takes most of the time is preparing the freezer for the install. Need to remove all shelving, (and the door) to gain access to the unit. The ice maker is simple to install once access is achieved. Putting everything back together takes some time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from Santa Fe, NM
- Parts Used:
- WR29X5171
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Ice maker kept on making ice
I ordered a new micro switch that was activated by the high ice lever. Once the switch was replaced the ice maker cut off as it should have and stopped producing too much ice. YHis job was of moderate skill level, the most challenging was replacing a spring that popped out then reassembling the unit.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Norwood, NC
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
No problems.
Took out the old, replaced with the new. Needed second person to hold the flash light. That is the secret to get it plugged in and secured.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Horseshoe Bay, TX
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker leaking
Quite easy. Turn off water supply and turn off ice maker at switch inside freezer. Unscrew the old unit, separate the electrical connection, and pull it out. New unit comes with parts that do not fit my refrigerator, so visually examine the new and old units, reuse any needed parts from the old unit, such as plastic water ramp. Reconnect the electrical connector, and screw it back in. Turn water supply back on and then turn ice maker back on at switch inside freezer. Discard unused parts. Wait up to 24 hours for new ice cubes to be made.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mitchell from Chicago, IL
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
The Ice Maker stopped making Ice because the arm over the ice bucket which turned turned on the icemaker was broken
I read the step by step instructions that came with the part. I turned two screws and disconnected the electrical harness and Removed the icemaker. Two other parts from the old icemaker were easily removed without any tools and put on the new icemaker. The new icemaker was put in the same way the old one came out. I reconnected the electrical harness and tightened the old screws. The hardest part of the whole job was reading the directions. They were easy to follow if you take the time to Just read them!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- George from Katy, TX
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
Ice Maker not making ice
The video on the GE site was great. Showed step by step instructions on how to remove the old ice maker and install the new one. Also helpful was the detail on the water chute which needed to be moved from the old ice make to the new one. Saved hundreds of dollars by not having to have a repairman do this work for me.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Verma Jean from Lincoln, CA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
my ice maker quit working
I watched the video from the link that was sent to me with the shipping notice. It was very easy to understand. I had no trouble at all. I'm 75 years old woman, however, and I can fix about anything. Don't be afraid to fix appliances yourself if you feel you have the knowledge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Garry from San Antonio, FL
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
ice maker not working
unscrew one screw unplug.insert the ice maker,put the screw back in you have ice less than ten minutes
Was this instruction helpful to you?
Thank you for voting!
Two items ordered had been broken for a while
Took out the vegetable bins, the glass and the shelf rack. Replaced the left side and the center glide. Worked easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Grimes from Bartlett, TN
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
ice maker very slow and arm that controls amount of ice sticking and quit making ice
took 1 screw out and removed ice maker and slid new one in and replace screw and connected power cord
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Eduardo from Arlington, VA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
No Ice...
Super easy, had my 15 year old do it (with my supervision).
Followed very clear Instructions that come with the replacement...
But, he could not get to the plug location until he removed 4 screws holding the motor assembly that spins the ice in the drawer and moved it out of the way...
Followed the rest of the instructions...
Works like a charm.
Followed very clear Instructions that come with the replacement...
But, he could not get to the plug location until he removed 4 screws holding the motor assembly that spins the ice in the drawer and moved it out of the way...
Followed the rest of the instructions...
Works like a charm.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Abilene, TX
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
ice maker was leaking water. Cubes were sticking inside tray.
Reviewed video which was very helpful. Loosened two philips head screws, lifted up ice maker, unpluged power suppy and reinstalled. One of the easiest replacements ever!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Sahuarita, AZ
- Parts Used:
- WR17X2770
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken slide rail
Your online helpful hints made it easy as pie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lani from Lakeside, CA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Ice maker made no ice and no water from dispenser.
After what I thought was a thorough troubleshooting of said problem I replaced the Water Valve Assy which was really easy as the video shared, but it did not fix my problem. I had forgotten to pull the water line apart at the coupling below the doors (this was a troubleshooting step in another area). The water not dispensing was due to the line being frozen! Putting all items in a cooler with a couple blocks of ice and leaving the freezer door open for the length of watching a movie, the water was flowing again. Still no ice though. Ice maker vs mother board at the rear of the fridge, Hmmmm. Went with the ice maker, watched video, ole Steve makes the plugs disconnecting look easy, I had to use a flat head screwdriver to open the clips (he doesn't mention that) and I had 4 screws where he had 3. Also he didn't mention about the instructions which gives you 3 options with your unit. I had to re-use my Plastic Stripper Plate along with the Fill Cup and Ice Maker Insert. After completion of installation and about a half hour later, I heard ice fall, Wooohoooo!!! Overall the experience will make me think to utilize PartSelect again when needed. Reasonable prices and decent shipping time. Now the freezer light is out...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carl from Broomfield, CO
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Ice make stopped making ice
Went to GE website and researched the problem for the model, determined that it was 90% sure it was the Ice maker, I ordered it and it arrived the next day, installed it and it began working immediately,
Was this instruction helpful to you?
Thank you for voting!