GSS25GSHJCSS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joe from Succasunna, NJ
- Parts Used:
- WR24X20456
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Gasket wasn't sealing
Replaced gasket. No tools requires. Just pull the old one out and press new one in channel with hands. TIP: heat the new one slightly with a hair dryer or a heat gun on low. Makes it more flexible
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sherrie from COTTLEVILLE, MO
- Parts Used:
- WR24X20455
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
Worn out gasket on freezer
I received part. I then used a hair dryer to smooth out kinks. Took about 15 minutes. Pulled off old gasket and replaced with new one. Used hands only.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tina from SCANDIA, MN
- Parts Used:
- WR23X25635
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
On/off light switch broke off in freezer section
Used a putty knife it pry off old switch, unplugged old switch from wire harness, replaced new 1 in, snapped back in place. Took about 2 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from LANDING, NJ
- Parts Used:
- WR24X20455
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Freezer Gasket was torn in some spots, freezer had condensation inside and could not maintain zero degree temperature.
Ordered gasket. Laid out gasket near sunlit window untangled and flat on carpet for 24 hours to insure it was pilable and correct shape. Removed the old gasket manually easily without any tools and cleaned the door's seal groove with a paper towel slightly soaked with Simply Green. Installed new gasket starting at the upper corners then inserting upper edge by tilting the gasket toward the inside of the door with my fingers. Then installed the lower corners along with the bottom edge. Proceeded installing the side edge working from the set corners inserting the gasket's inner tongue into the door groove with my fingers again tilting the gasket inside the door. Once the gasket was installed, I closed the door and guided my fingers along the gasket to insure the magnetic edge formed a firm seal. This is wear the DIY videos suggested applying petroleum jelly but I did not need it since the gasket was pliable enough. Overall, the effort took 15 minutes because I think laying out the gasket for 24 hours allowed it to settle into its desired form..
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Crista from Canal Winchester, OH
- Parts Used:
- WR24X20455
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
Our freezer door wasn’t sealing properly
It was so much easier than I thought. First we used a hair dryer to loosen everything up. Just pulled off the old on (with our hands) and put the new one on. Then went around the edges and wiggled it into place. There are plastic ridges that if fits into, so it’s important to make sure every part is sealed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pa Pa from BALTIMORE, MD
- Parts Used:
- WR24X20455
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Freezer ice buildup
I replaced defrost sets, door gasket but still ice buildup freezer part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Santa Clarita, CA
- Parts Used:
- WR24X20456
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Replace Refrigerator Gasket
The customer service was outstanding. Ordered Monday and part arrive next day. I used a nongrease silicon spray on the gasket and it slipped into the slot without a problem.
Was this instruction helpful to you?
Thank you for voting!