CZS22MSKGHSS General Electric Refrigerator - Instructions

Simply remove the old dispenser and replace with the new one

Just followed the partselect video. Very easy after you watch the video a couple times. Pull out fridge, unplug, turn off water, unscrew bottom panel and top cover and inside screws, take water connectors loose, put old unit out. Reverse to put in new unit. While I had the fridge out I vacuumed and dusted the coils. Thanks Parts Select.

Cut off water supply. Remove rear lower panel. Disconnect 2 lines done

Repair went well. All i needed was the more expensive part. The other I did not need.

Installed the drawer. Boom! Done.

The repair is a snap, you can watch the video and it will put you on the right path. My story is more about the service that Part Select gave me. I used a small box fan on low as a temporary fix. My model number was worn off from the box wine we store in that particular place. So I ordered the part based on looks, well it was wrong. Called Part Select and we talked, the nice lady on the other end said OH it must be this fan motor. Send us back that one, and I'll get this out too you. I'll credit your account for $7.99, and it cost me $8.99 to ship back the wrong part. Wow, the next day I received the new motor. They sent it overnight! I thought it would be 5-6 days! Unbelievable. I will use this company for any, and all my repairs.

Used nut driver to remove two screws at top of tube, and the three screws holding composite cover on back of fridge. Pulled out the upper portion of tube, pulled up on fitting and removed lower portion of tube. Put upper spout portion of new supply tube into position, replaced two screws, pushed lower portion of tube into locking fitting on supply valve solenoid. Replaced composite cover with three screws, and was done. Entire job took less than 5 minutes. It took longer for me to find my nut driver set, than it took to do the repair. I ordered the part online, and it was delivered to my door in a lightning fast 36 hours. Hopefully I won't ever need any more appliance parts, but with your easy to navigate website, fast shipping, and fair prices, you have won me over as a customer. I will refer you to friends because of your high speed, low drag, zero defects, excellent service. Thank you very much. Rich.

Just as described in earlier reviews, this was the filter housing unit and not the double water valve. To determine which part is failing bypass the water filter unit by disconnecting both water lines and connecting the fresh water line directly to the water valve. If this solves the problem, then you know for sure the filter housing is the problem. The filter housing has a very small tab that pushes open a rubber flap valve when a filter is installed. This allow you to remove the filter without turning off the water supply. Apparently only a very small amount of wear prevents the flap valve from opening fully and allowing water to flow. A small amount of water flow may be evident with the water dispenser but the ice maker will keep working until flow is completely interrupted. Easy fix.

I identified the noise was coming from the coils / and the fan. Cleaning the fan helped reduce the noise a bit but it still kept recurring. I ordered the part, which was really easy using the diagram on the website. The instructions and the video were really helpful and was able to remove the old motor and replace it with the new one with relative ease. While there I cleaned the fan blade and vacuumed the surrounding area. This whole repair went quite smoothly and has given me the confidence to take on other repairs before calling out the repairman.

Turn off the cold water at the source. Remove metal plate from back of refrigerator at the top. Disconnect the two tubes that feed the water to the filter at the bottom of the back (behind the cardboard), noting which line takes the "blue" tube. On the inside of the refrigerator, pop off the top of the filter housing and set aside. Unscrew the two screws holding the filter assembly from the inside and pull the old assembly through.. Remove the plastic stopper (unless you are not using a filter) from the new assembly.Thread the new assembly tubes from the inside to the outside and reconnect screws and replace top of filter housing. Connect the new tubes to the water supply and to the refrigerator and tighten the nuts. Replace the metal plate and screws over the black insulated part at the top. Turn on the water and check for leaks. Replace the water filter..If a 68 year old grandmother can do it, so can you.

Very limited working space in this model. Must remove grill and disconnect elect connector on motor. One additiional tool suggested: Extendable rod with magnet on end because you will most likely drop something. First, remove two screws holding motor to metal strap. Tool must be inserted between blades of fan in order to get to the screws and this is the hard part. Fan and motor are removed as one assy and this takes some manuvering. Might have to remove front screw on metal strap to gain more room. I did not attempt to remove fan shroud. My fan was attached to the motor shaft with a metal clip. Spray a good lubricant such as PB Blaster on the shaft, wait a few minutes and press it or tap it out gently. Save misc parts on old motor for reassembly. Your set up may be different so check out everything before starting.

Turned off water supply, removed bottom rear metal panel,with a towel to catch water pushed in and removed water line from double water outlet, removed metal clamp and then grommet tube assembly from top right rear of refrigerator. Then I put in new grommet tube assembly, turned on my water and checked for leaks.