MSG20GWXDWH General Electric Refrigerator - Instructions

Removed door off hinge , remove bottom hinge, drill out rivet, lift off old cam & replace with new cam ,add new 1/4' BOLT(NOT SUPPLIED) to location where rivet was, reinstall bottom hinge & door ,check alignment, works perfect.

Thanks

Placed blocks under the refrigerator door to take weight off the lower hinge pin. Removed the hinge by removing two screws into the refrigerator and two screws into the bottom of the door itself. This allows the hinge to be removed so the old nylon "closer" pieces can be removed (the one attached to the refrigerator has a rivet holding it in place so that has to be drilled out and replaced with a 3/16 inch bolt and nut). After re-attaching the nylon "closer" to the refrigerator side of the hinge and placing all the shims back in place, I re-attached the hinge to the door first, then the half hinge to the refrigerator. Had to line up the holes, tighten the screws and presto, the door closes like it was new again.

The freezer door side is more difficult as there are wires and a water line to work around.

BUY TWO CAMS! Just like the others, both of the cams were shot. My husband & I did this ourselves & have NEVER attempted appliance repair before.
We propped the door up high enough to access the bottom hinge piece on the fridge & removed using socket. Removed the cover from the top hinge. Slid door down off the top hinge in able to get to the cam on bottom of door. Replaced this cam 1st in order to get door back on while worked to get the old cam off hinge. As others posted, this is rivited on. Used grinder to grind off rivit & hammer & punch to punch out. Attached new cam with bolt & nut found in our tin of leftovers. Inserted hinge into door & reattached to fridge. DONE! Not hard at all & didn't even argue the whole time.

took top bracket off--then removed door--took
bottom bracket off bottom of door and replaced
door closing cam and reasembled---a piece of
cake

After reading the stories here, I purchased one door closing cam. After getting into the problem area, I realized I needed 2 cam, so I put the door back together and ordered another cam. If you have this problem, buy 2 cams.

First, I was glad I read other posts on this repair as I would have only purchased one of the replacement cams when I needed two! I removed the top door hinge with a screw driver (cover) and small socket set for the door hinge. I then removed the door and removed the bottom hinge (socket set). The bottom hinge had a small rivit that held the bottom cam in place. I used a hack saw to cut off the rivit and replace the cam and secured it with a small machine bolt and nut. I then laid the door on its side and removed the top am from a bracket attached to the bottom of the door. I relaced the cam (second one) and reinserted the screws. I reattached the bottom hinge and then placed the door on the bottom hinge pin. I then held the door in place while inserting the top hinge pin bracket into place and retightening the top screws. I replace the cover with a screw drive which was the ahrdest part in trying to find the hole the small screw gets inserted into. DONE!

Like the rest of the other statements it was easy with 2 2X4 pieces of wood to block the door up. The other suggestion about buying two of the pieces was a good idea. Once I took off both the top and bottom pieces they were both worn out and it was easy to replace them both at the same time. The door is working good again and shuts on its own.

Please note that I did this repair 2 times before and it was very easy, it took me longer to get the stuff out of the refrigerator door.

But this time the existing upper and lower cams broke, and the lower part of the door was making contact with the screw that holds the lower cam to the lower support bracket damaging the head of the screw.

Now I could not use a screw driver and I had to use a wrench and a vise grip to hold the round screw head (not easy), and then replace the screw and nut.

I had to insert 2 flat washers under the lower support, to separate the door an additional 1/32 from the ref. base to accomodate the fact that the door gasket had lost its regular shape in the lower part of the door (I discover this when I dismounted the door).

Then I removed the damaged cams, replace them with the new ones and now it is working ok.

Manny

I learned from previous descriptions. Most important is there are two cams so order two. Second is that the door can be blocked from the bottom so the door doesn't have to be unloaded if you are careful. Remove the vent cover. Raise the door as high as possible while closed then block it from dropping down. I used wooden blocks. Remove the lower hinge and bracket on the bottom of the door. Put everythng back and you're back in business. A kit with both cams, spacers, and screws with diagram would have been nice to have.

unclipped and replace with new part.

Turn off power
Remove operator faceplate by pullling out on outer lower corners
Disconnect wire connectors from circuit board
Remove four screws from dispenser and pull out dispenser assy
Replcae Door ASsembly
Put everything back in place
Power up
Job Done

Watched the video very good. Thank You

Excellent video was available on the Parts Select website. It was simple. The selector panel pulled out by hand from the bottom. The subpanel was removed with the four screws. The flapper snapped out of the holder with two clips. The new one was inserted in reverse order.

Under the control panel there are three small holes. Insert ballpen or small flat screw driver on both outer holes to push a tab lock that holds the control panel in place. Then pull out control panel and three set of wires will be exposed and disconnect wire connectors (connectors have different sizes so you wont get confused in reconnecting). Unscrew four screws on each corner that holds the ice dispenser assembly (a part where you push your glass against to dispense ice or water. The flapper is exposed and easy to replace.

Replace the flapper and this solved it. The video provided was excellent and allowed me to do this repair myself.