PNR22MSEBFES General Electric Refrigerator - Instructions

After confirming that a frozen water line was not my issue, I confidently bought this item and installed it within minutes after receiving it! It is easy to install - just close the connection to your refrigerator, open the rear lower panel, disconnect the water tubings and electrical connectors. Reverse that - you have the installation. Plug the refrigerator back on, turn the water back on for the refrigerator - and observe for any leaks. If no leaks - try dispensing water. Working great for me! My refrigerator's model is a GE, model # zfsb26dnass.

This repair is EXTREMELY easy to conduct even for the novice. The first step was to shut off the water supply at the wall, and disconnect the power cord to the refrigerator. Remove the six panel screws to remove the lower back panel. On the lower left hand side is the water valve. This is connected by only one screw, so that was removed. Compare your new valve with the one you are removing to double check that the units are the same. Disconnect the inlet water supply line and connect it to the new unit. Disconnect the two water outlet lines from the old unit and connect to the new unit. Finally, disconnect the two power plugs from the old unit and connect to the new unit. These are all colored coded or different sizes, so there is no way to fowl this up! I just recommend disconnecting and reattaching one at a time so that you are doubly assured you are doing this correct. Reattach the valve unit back onto the side of the refrigerator. At this point, I turned on the power and water supply to check for leaks. Also, have someone run the water in the ront panel dispenser to ensure things are working properly. Once that is completed, reinstall the back panel and you are done. I did this project about two weeks ago, and things are working great now. Saved a lot of time and money by doing this job myself.

it was easy. Open the fridge,untwist the old filter. Open the new filter, fill with tap water and twist in place. Run water through it for a few minutes to insure it is working and filters the water.

Simple repair. I first shut off the water supply to the unit. I then removed back cover from lower part of the unit. The water valve is on the lower left side. I began by removing the screw on the bracket that holds the part in place. This screws into the back of the unit. I then disconnect the water line by unscrewing the fitting. Then unplugged the two electrical connections in the back of the unit. Lastly, remove the two hoses that plug into the bottom of the the unit. The installation was essentially the reverse of the the removal. The whole process took about ten minutes.

Frig parts had been scavenged in an apartment complex. Restoring socket was only a matter of plugging in two spade contacts and clipping in socket.

It was as simple as taking off back panel and disconnecting 3 tubes and and two plugs to remove old valve and attaching the new valve piece to the 3 tubes and two plugs! It actually took more time getting the panel off than making the repair AND it saved us a little over $300 as the repairman quoted a price in excess of $350 to repair it. He was actually the one to tell us to buy the part ourselves and repair it. We are thankful being able to get the part and for an honest repairman.

turn off water remove back cover remove 1 screw holding water valve use wrench to remove main water line input push up holders on bottom of selinoids pull both output lines loose disconnect two electrical plugs reinstall new valve in reverse order

PartSelect helped me identify the part, got it in only a few days and I followed the easy to follow video featuring Steve. Awesome!

I was unplug the electrical,closed the water line.replaced old water outlet with the new one;and there work fine.Thanks

I shut the water supply and took off the rear panel.
One screw released the valve. Pulled off water lines(3) and electrical connectors and installed all on new valve. Screwed the valve and the panel back and turned on the water supply. Prior instructions on website helped. Part came in two days. This part should have never failed. Looks like the housing is two parts glued together. Glue failed after 7 years. G.E. should cover this. My warranty expired after 5 years. M.K. Boca Raton,Fl.

It was very simple. Pull the fridge back (unplug and turn off water), remove the cardboard backing and disconnect/unhook the current water valve and reverse the process to connect the new.

1. Remove back cover from frig
2. Remove Double Outlet Water valve from frame
3. Place towel under valve, remove supply line to filter
4. Cut black and clear lines next to valve, ensure a smooth cut
5. Slide new connectors onto lines, press lines into valve firmly, make sure they slide in all the way
6. Slide connectors into valve locking into place
7. Re-connect filter supply line and re-connect valve to frame making sure lines are in the proper place
8. Replace back cover of frig, do not over tighten screws

per the video - took off panel, remove the existing part, and replaced.

very simple repair.....push two hoses into compression fittings on the bottom, plug two wire harnesses into the back, and put a screw into the front to attach to the refridgerator frame. After that, just turn water back on and plug it in. Ran great.

Part also came in quicker than expected......which was a definate plus.

Unscrew the mounting screw and cut the tubes as close as you can to the valve. You cannot reuse the valve as the self sealing lock washers will be destroyed once you take out the tubes. Push the newly cut tubes into the new self sealing new valves and remount. Easy Peasy!