PNR22LGEBFBB General Electric Refrigerator - Instructions

Followed the instructions from your site and they were perfect. Unfortunatly that wasn't the problem. It still doesn't work.

replaced double outlet water valve. Valve works as it should. Shipping was much quicker than I expected.

turn water off to ice maker,unplugged refrigerator, took back panel off took old part off and put new part on

Followed instructions others posted. No need to cut any water lines, just push the white collar on the new valve, pull out line and do the same to install lines. Only issue was inlet line leaked after initial installation. It was leaking above the connection, so teflon tape wasn't the answer. Answer was to hold the line in exactly the routing place it was before removing.
It took a few days for ice machine to return to normal (as in making ice in quantity), but works like a champ now.

Just put on, part was great. Will buy parts again from this company.

Unplugged fridge, shut off water supply. Removed bottom back panel of the fridge and carefully vacuumed up all the dust. Located the water valve to the left of the compressor. It is attached to the side of the fridge by a metal bracket. Remove the screw from bracket and lift up on the whole assembly. Now I removed the electrical connectors and pushed in on the quick release tabs to pull out water lines. When installing water lines to new valve be sure to push them all the way in. The water lines are marked so you will know how far they must go in. Attached electrical connectors and remounted whole assembly back to the side of the refrigerator. Turned on water supply and plugged fridge back in. Checked water dispenser for proper operation and also checked water valve for leaks. Reattached the back cover to the fridge and that was it.

1)turn off water supply to appliance 2)disconnect appliance from power supply. 3)remove grill. 4)remove valve retaining fastener. 5)disconnect two wiring devices. 6) depress retaining devise at each water line to disconnect. note: if the lines do not releace, use utility knife to cut lines as close to unit as possible. 7)attach new valve in reverse order.

1. Remove back cover from frig
2. Remove Double Outlet Water valve from frame
3. Place towel under valve, remove supply line to filter
4. Cut black and clear lines next to valve, ensure a smooth cut
5. Slide new connectors onto lines, press lines into valve firmly, make sure they slide in all the way
6. Slide connectors into valve locking into place
7. Re-connect filter supply line and re-connect valve to frame making sure lines are in the proper place
8. Replace back cover of frig, do not over tighten screws

I went on Google to get GE Tech Manual. But really, undid screws for back plate; Dismounted (1 screw) Water Solenoid assembly; disconnected 3 water hoses into solenoid; unplug two power connectors. Then reversed the process with new Water Solenoid...works great!

I watched the video instruction and it was very easy to replace. took me less than 30 minutes.

removed rear cover of Frig, found valve was cracked and leaking water. turned off water and ordered new valve. After receiving new valve, Removal and installation took about 15 minutes. Pretty easy, a no brainer.

It was very simple. Pull the fridge back (unplug and turn off water), remove the cardboard backing and disconnect/unhook the current water valve and reverse the process to connect the new.

pullee refrigerator out to get to back un pluged power took off back cover unscrewed one screw to loosen water valve unscrew water inlet line ther are two water lines in back of water valve i cut them as close to water valve as i could push the water lines that i cut off into water valve makin sure in the rigfht place they are quick disquinect just push in and ther on screwed water valve back on connected water inlet line replaced back cover pluged in power pushed refrigerator back in and was done it had to run for a little while to get the air out then worked fine

Unscrew the mounting screw and cut the tubes as close as you can to the valve. You cannot reuse the valve as the self sealing lock washers will be destroyed once you take out the tubes. Push the newly cut tubes into the new self sealing new valves and remount. Easy Peasy!

per the video - took off panel, remove the existing part, and replaced.