Models > PDRF0MBYCRBB > Instructions

PDRF0MBYCRBB General Electric Refrigerator - Instructions

Jump to:

All Instructions for the PDRF0MBYCRBB
121 - 135 of 181
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Bill from Warrenton, VA
Parts Used:
WR55X10025
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Refridgerator not cooling, freezer frosting over
First, I had to remove the freezer drawer front. This is 8 large phillips head screws. then remove the plastic cover over the drawer slides. to do this, remove the white center screw from the slide near where it attaches to the drawer front. then the plastic cover will slide off pushing to the rear of the slide. take off the slides from the freezer walls by removing the phillips screws and pulling them towards you. They have tabs/slots in the rear. remove the center tray support and support bars, too. the icemaker has to come out, that is just 2 phillips screws but you also have to disconnect the electrical connector. just squeeze the locking wings and rock/pull. a screw in the top center of the back panel comes out. Lift and pull the back panel out. The evaporator coil appears. The thermocouple is attached to the coil in the upper right. Cut that one's wires and take it out. Just cut back about an inch from the back of the thermocouple, there is not much slack. Seperate and strip the wires back about 3/8 inch. Do the same for the new thermocouple. I twisted the wires together and used a solder sleeve to join the wires. The sleeve is just a little plastic tube that has a ring of solder in it that melts with heat gun heat. You can join the wires using butt connectors or whatever method appeals to you. I just wound the extra wire and put a cable tie around it, there is plenty of hiding space in that area. Make sure the new thermocouple is contacting the coil firmly.At this point, for a test, I left everything apart, propped the drawer against the opening and plugged the fridge in. Note that the evaporator fan will not start spinning immediately! It will just sit there making little bumps like it wants to go. The temp in the coil has to get settled before the electronics in the refridge will tell the fan to spin. It takes maybe 20 minutes. Reassemble. Fridge and freezer work great. It does take several hours for all to get cold again.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Edward from New Smyrna Beach, FL
Parts Used:
WR60X10209
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Socket set, Wrench set
Condenser fan not working. Freezer & frig heating up
Very limited working space in this model. Must remove grill and disconnect elect connector on motor. One additiional tool suggested: Extendable rod with magnet on end because you will most likely drop something. First, remove two screws holding motor to metal strap. Tool must be inserted between blades of fan in order to get to the screws and this is the hard part. Fan and motor are removed as one assy and this takes some manuvering. Might have to remove front screw on metal strap to gain more room. I did not attempt to remove fan shroud. My fan was attached to the motor shaft with a metal clip. Spray a good lubricant such as PB Blaster on the shaft, wait a few minutes and press it or tap it out gently. Save misc parts on old motor for reassembly. Your set up may be different so check out everything before starting.
Was this instruction helpful to you?
Thank you for voting!
Customer:
James M. from Belfair, WA
Parts Used:
WR55X10025
Difficulty Level:
Very Difficult
Total Repair Time:
More than 2 hours
The frig was not cooling in main section or freezer
I ordered 3 temperature Sensors Part#PS304103 and viewed the video. Got there, opened the frig. and it looked totally different and no place in any part of this frig. that took these sensors as viewed on the video. Totally baffled why these parts were listed for this frig. there was no place in this frig that would access for these parts. Serial # was HR443071.Maybe this model is out of date for these parts. Trying to find someone who can repair it. Any ideas???Purchased this GE in 2008. Model #is GSS25WSTFSS Thanks, for your help. JIM
Was this instruction helpful to you?
Thank you for voting!
Customer:
Aaron from Montebello, CA
Parts Used:
WR72X10073
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
broken slide pan lh
pull out the slide pan lh and replace for the part
Was this instruction helpful to you?
Thank you for voting!
Customer:
Kathleen from Burke, VA
Parts Used:
WR72X10072
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
The plastic piece that holds the screw in on the pan of the refrigerator had broken
I took the pan out, replaced the bar with the new part - slide pan RH - and I was back in business. It couldn't have been easier.
Was this instruction helpful to you?
Thank you for voting!
Customer:
DAVID from WILLIAMSBURG, VA
Parts Used:
WR23X21444
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
light switch in freezer broke
Used small screw driver to pry the top of the switch away from left inside wall of freezer side of side-by-side refrig./freezer; then used pliers to remove the switch; then removed the 3 prong socket and plugged it to new switch and installed it into the inside wall of the freezer.
Was this instruction helpful to you?
Thank you for voting!
Customer:
TREVOR from KENT, WA
Parts Used:
WR72X10072
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Wrench set
broken slide drawer track
Took out shelf, unscrewed old track, screwed on new track. Only thing is not a standard flat or Phillips screw head so if you don't have a star head bit, you are out of luck.
Was this instruction helpful to you?
Thank you for voting!
Customer:
ANTHONY from NEW EGYPT, NJ
Parts Used:
WR23X37285
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Pliers, Screw drivers
sticky switch
easy pry out, disconnect wiring, connect on new switch and press in switch.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charles from Durham, CA
Parts Used:
WR55X24064
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
compressor running and hot, refer and fridge room temp.
Watched a youtube on capacitors- though on a motor with a pulley, the symptoms were the same, motor running and pulley not turning-bad capacitor. Took a chance for a 17+ dollar part vs a new compressor. It worked.
Was this instruction helpful to you?
Thank you for voting!
Customer:
JOSE from NEW YORK, NY
Parts Used:
WR55X24064
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
fan and compressor wont start
Googled the model number of refrigerator with symptoms of "refrigerator wont run". Parts select web site appeared on my screen, opened Parts Select website, Partselect said probable cause of my frige symptom was that the run capacitor usually burns out 51% of the time. They were correct with the diagnosis 100%. I ordered the run capacitor for $23.00, installed it in 10 minutes, refrigerator runs good as new. Thank you for saving me cost of service call. I probably saved $200 or more. I will use Partselect again with my next problem. THANK YOU,
Was this instruction helpful to you?
Thank you for voting!
Customer:
Richard from Northport, NY
Parts Used:
WR02X12898, WR02X12897
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Broken basket holder
Snap on. Web site ver easy and received the parts in two days
Was this instruction helpful to you?
Thank you for voting!
Customer:
philip from cocoa, FL
Parts Used:
WR55X10025
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver
freezer would not defrost
There were only 3parts listed to check omed out the defrost heater and thermostat ....thermistor checked bad ordered replacement took less than 2 minutes to replace after I defrosted it again runs fine
Was this instruction helpful to you?
Thank you for voting!
Customer:
Charles from Williamsburg, VA
Parts Used:
WR2X9391
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
needed new light socket
Pulled out old socket.pushed in new one.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Jeffrey from Saint Charles, IL
Parts Used:
WR55X10025
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Pliers
refrige ws too cold
as per video
Was this instruction helpful to you?
Thank you for voting!
Customer:
christopher from collegeville, PA
Parts Used:
WR23X37285
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
no light in freezer
Connected the 2 wires and pushed in the switch until it clicked.
Was this instruction helpful to you?
Thank you for voting!
All Instructions for the PDRF0MBYCRBB
121 - 135 of 181