38451HBRERWW General Electric Refrigerator - Instructions

I did folllow the instructions on the video step by step.

I removed the shield over the timer and the part that supported the timer. Just unpluged it and pluged in new timer and put back shield. I had already replaced the defrost heaters which had totally burned up. I also replaced the thermostat while I was making the repairs although the old one was still o.k. All the information that I needed to make the repairs I obtained through your website. After looking at several websites to compare prices-etc, I found yours to be the best overall. Thanks-a-million your website is worth it's weight in Cold Food !

Refrigerator is not cooling. Light and fan working. Changed the capacitor.. Still not cooling. Back to discovery mode.It may be the timer
Certainly not PartSelect's fault. They have great service.

I had lost the bottom hinge during a move and so I rigged the hinge using an old tv antenna and the door never really quite worked right and it was VERY annoying. I stumbled upon this site and was surprised how inexpensive the part I needed was. I was very impressed with the speed of shipping and the install took maybe 5 minutes. The fridge works as good as new. Thanks a ton!

common sense,removed plate,removed mounting bracked,unplugged,reversed order,and that was it.

took out 4 screws - lowered timer cover - replaced timer- put it back together

It has been my experience that these motors sometimes die when the refrigerator is overfilled and motor strains to keep refrigerator cold. And this motor is used in several models of refrigerators. That said, sometimes the hook-up is slightly different between other units. The available video is good, but like I said, circumstances will be slightly different between various models.

After cleaning out freezer (plug disconnected first), start to remove outer plastic covers. If you want to keep track of the different steps, you can take pictures with your cellphone. And if there are any connecting wire attachments you think you might not remember, again, you can take a picture, or label with tape (colored tape, or by writing on the tape). And for keeping track of the different-size screws, I place them in a muffin tin, keeping an order of left to right and top to bottom in the tin. When removing Styrofoam blocks in bottom center, make sure you remove any remaining ice underneath in the hole so refrigerator can "breathe". Freezer air is moved below to refrigerator compartment, so a blocked vent hole will strain refrigerator as it tries to maintain its temperature setting and can be the cause of your failed motor.

After replacing motor onto bracket with grommets and blade, don't completely tighten. Position plastic cover with hole opening over motor and blade assembly. Twirl motor blade to see if there is any interference with cover. If not, take away cover and tighten motor on bracket. If there is any rubbing, adjust motor/blade assembly accordingly before tightening in place. Putting everything back together is in reverse order.

Easy fix - snapped together.

4 screws in the freezer and the back panel came off then 2 more screws to take the motor off. I unpluged the old motor pluged in the new motor put the back panel back on and I was done.

First I removed the left condensor fan motor bracket nut, loosened the right motor bracket, dropped the moter bracket down freeing the motor from the rubber grommets.
Pulled the fan off from the motor shaft, pressed the new fan on the shaft and installed new grommets. Replaced the motor bracket and tightened the right bracket nut and checked fan for clearance and free spin. Reinstaled the left bracket nut. Turned on the refrigerator and checked fan for action. Everything worked great.
I did not know the fan replacement came with a compression ring already installed, so now I have an extra compression ring.

first I ordered parts that didn't work. the return process was painless and I found the part I needed, which just popped right in!

From instructions found on the site I was directed to the defrost timer part being bad. And from the information others posted that have had the same problem I was able to replace that part by removing the bottom grill just below the door and on the left side was the part. Removing one screw to remove the bracket from the frame and then another screw to remove the part from the bracket. I found it easier to remove the part from the bracket before I pulled the part out so I would have more room to unplug the connector. Just reverse the steps to replace the new part. It took about a day or so for the refrigerator to get to the proper temp.

Repair was a no brainer. More important, Part Select was extremely efficient. Customer Service was very helpful as my model number was not available on line. Thanks for your wonderful and prompt service. Rich L.

Despite attempts to quiet the 2 year old fan, I went ahead and replaced it. Part Select was prompt with a new one at my door less than 24 hours. It was just the fan motor, so took a couple extra steps to place it in the metal housing, but no problems and though the frig still makes noises, it's not coming from the fan as before.

Followed the instructions on the repair video and it made very easy. Also saved us a lot of money. Thanks for your help.