TBX21ABRRWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Mary from New Milford, NJ
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Cap on the door retainer bar broke.
The replacement cap fit perfectly. Unfortunately when the orinigal cap broke it tookout a small piece of the surrounding plastic leaving nothing for the new cap to catch. I have the piece and tried several kinds of glue but nothing holds it securely enough. I would however readily recommend your company. The service was terrific.
Thank you.
Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kaye from San Francisco, CA
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I didn't know if I could get a replacement part, but I googled "replacement parts" (or some such), and since this website looked easy to navigate, chose it. (Actually, I did my ordering via telephone). The sales rep. helped me clarify which part I needed, I ordered it, and received the part the very
I simply snapped the two end pieces into place, attaching the guard rail. It was like putting the pieces of a very easy puzzle together‚ especially for someone like myself who is mechanically challenged.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Travis from North Quincy, MA
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Old end cap broke.
Put the new end cap on and snapped it into place, took about 5 seconds.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Northglenn, CO
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The above door End Cap broke.
The repair just required snapping the new part on to the door shelf and then snapping the shelf in to the door.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joyce from Tacoma, WA
- Parts Used:
- WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
light wouldn't come out of socket
It just unpluged and the new one plugged in. Simple. The part was reasonable and arrived very quickly. It sure is nice to have a light in the frig again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ruchik from Bronx, NY
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken shelf retainer bar end cap.
I ordered 2 end caps just to keep one as spare. Turned out I had ordered a size larger than the one already on the refrigerator. So I replaced both ends and it worked fine - with increased shelf space. Now I can even fit a gallon container with ease!!! Took about 20 seconds. I just wish there was an easier way to measure parts before ordering. Otherwise, the entire process from order to finish took about 3 days.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sammy from Farmington, NM
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The plastic parts that hold the brackett to the shelf were broken.
The part just snapped into the shelf bar. Extremely easy to fix. Since you show the part in a grid I was able to tell, by holding my old piece up to the screen, that the new part would be the correct size. We have rentals and are always needing parts for appliances. Impossible to find locally.
Also the part came so quickly it was almost as good as buying it here in town. Thanks. Donna Bingham
Also the part came so quickly it was almost as good as buying it here in town. Thanks. Donna Bingham
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jamie from san clemente, CA
- Parts Used:
- WR71X10077
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door shelf bar was bent and no longer holding in items
we ordered new bar, cut to fit with instructions, and voila! easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tara from cumming, GA
- Parts Used:
- WR24X446
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
needed to replace the gasket because it had become brittle
My husband thought he would have to set aside time on the weekend to replace the gasket. It was delivered and I unpacked it put it on and that was that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from POCONO LAKE, PA
- Parts Used:
- WR60X10168, WR02X10098
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
the condenser fan motor was intermittently verynoisy. obvious sign of a (possibly imminent) failure
1 unplug the appliance
2. remove the rear cardboard cover, giving access to the compressor and condenser area
3. remove the two (condenser motor bracket) mounting screws, then with the motor assembly in your hand remove the the fan blade which is friction mounted to the motor shaft( note the exact position of the fan blade on the motor shaft so you can replace it in the same position when you reassemble), remove the two wires connected to the motor. Also remove the rubber resilient mounting grommets on the motor mount frame as these can harden with age and cause excessive vibration.
4 install the new motor into the mounting frame with the new grommets
5 reconnect the two wires to the new motor (non polarized)
6 secure the mounting frame (with the installed new motor) back in place
7 slide the fan blade onto the new motor shaft
8 screw the rear access panel back in place
plug in the refrigerator. the next time the compressor and condenser fan cycle on, verify operation of the new condenser fan motor
2. remove the rear cardboard cover, giving access to the compressor and condenser area
3. remove the two (condenser motor bracket) mounting screws, then with the motor assembly in your hand remove the the fan blade which is friction mounted to the motor shaft( note the exact position of the fan blade on the motor shaft so you can replace it in the same position when you reassemble), remove the two wires connected to the motor. Also remove the rubber resilient mounting grommets on the motor mount frame as these can harden with age and cause excessive vibration.
4 install the new motor into the mounting frame with the new grommets
5 reconnect the two wires to the new motor (non polarized)
6 secure the mounting frame (with the installed new motor) back in place
7 slide the fan blade onto the new motor shaft
8 screw the rear access panel back in place
plug in the refrigerator. the next time the compressor and condenser fan cycle on, verify operation of the new condenser fan motor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paypal_shipping_address from Ripon, CA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Light would no longer turn on
I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jodi from Benton Harbor, MI
- Parts Used:
- WR23X37285
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Light out
Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from O'Fallon, IL
- Parts Used:
- WR24X446
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
bottom of gasket deteriorated and let in warm air
i pulled the old gasket off, and placed the new one in place, starting at the corners. then i lined up the insert in the gasket with the gap where it is to go and ran my fingers along the gasket, pressing in with my thumb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from Pensacola, FL
- Parts Used:
- WR17X2770
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
the plastic part had broken and wouldn't support drawer
Replacing the new part wasn't hard, just very time consuming and frustrating. I had to remove two-thirds of the shelving of refrigerator as broken drawer slide was on the bottom and I had to have room to remove old and replace new. Of course, then I had to CLEAN all the drawers and shelving before replacing them and then, because they were fresh and clean, I had to remove the other third of shelving and wash and replace it. So, it was an hour-long or more time. I love your business, and had no idea I could get so many parts for old applicance and replace them myself, and I am a 70-year-old woman! This was the 2nd time to use your site and I will return to it again when needed. Thanks for prompt and reliable service and a site that makes it easy for a neophyte like me to find the broken part ! Keep up the good work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Phyllis C. from Northwood, NH
- Parts Used:
- WR17X2769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Slide rail broken at forward mount
Took out shelf & brackets. Removed plastic shelf. Unscrewed broken bracket & screwed in new bracket.
Put back in & replaced the shelf.
Put back in & replaced the shelf.
Was this instruction helpful to you?
Thank you for voting!