TBXC19ZPBRWH General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Henry from West Seneca, NY
- Parts Used:
- WR9X502
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Frezzer would freeze up, refrigerator stayed cold, solved the problem. Now the refrigerator seems to be running more than usual.
Checked the defroster coil which is located behind the rear panel in the freezer compartment, it was still working. Followed the schematics down to the defrost timer, which is located in the lower front of the refrigerator and tried that. Plugged in the new part and the problem is solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dawn from Wilton, ME
- Parts Used:
- WR24X450
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
Door gasket had rotted on the bottom
Soaked the new gasket in warm/hot water and snapped it on without any hassels. Thank you also for the fast delivery!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- theodore from salisbury, NC
- Parts Used:
- WR60X30349, WR60X114
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
bad fan motor
take fan out,put new in
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- thomas j from jim thorpe, PA
- Parts Used:
- WR24X450
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
liquid in bottom of refrigerator
took door off removed old gasket which was the hardest part of whole job put new gasket in place pressed into grove and rehang door need something to hold door up in place to reattach.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- KIRK from Malibu, CA
- Parts Used:
- WR9X502
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Freezer work refierator compartment is warm
Defrost timer is hidden in the control panel in the refrigerator top middle. Turn to off and remove two screws which are hidden behind white tabs. I had to pry the old timer from the plug with a screw driver because it was tight. Try not to short across the terminals. Plug in the new timer. Replace it in the clip where you got old one and reinstall the controls. The freezer was still all frosted up so I had to remove the cover and defrost it with a hair dryer to get it to work. Then I turned it on and it works great.
Was this instruction helpful to you?
Thank you for voting!
Retainer strip for door bottom not available
We bought the side door retainer strip with the hope we could simply cut it to length and it would be the solution for the top/bottom retainer strip not available.. The problem was the holes for the flathead screws on the door bottom do not match the pattern of the holes on the side retainer. This meant we had to mark and drill new holes carefully on a drill press and then cut the piece to fit. After that it was no problem at all to screw it back to door and install the new gasket. Sure wish the top/bottom retainer strips were in stock somewhere.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Seatac, WA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
switch wouldn't come out anymore and turn light on
Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Donald from North Chesterfield, VA
- Parts Used:
- WR72X273
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Right side rail of meat drawer cracked
Less than 5 minutes needed to remove cracked rail and replace with new rail. Must have a star wrench to perform task. Very simple task!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Williamsburg, VA
- Parts Used:
- WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
needed new light socket
Pulled out old socket.pushed in new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANTHONY from NEW EGYPT, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
sticky switch
easy pry out, disconnect wiring, connect on new switch and press in switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christopher from collegeville, PA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
no light in freezer
Connected the 2 wires and pushed in the switch until it clicked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Pedro from Miami, FL
- Parts Used:
- WR60X187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fridge not cooling
Fairly easy I pull the fridge foward and remove the backing board and notice the fan wasn't working, so I remove the fan and bench tested and it was burned then I clean the condenser with compress air if you don't have air then a vacuum cleaner works then once the part arrived I install it the now if working very good
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lloyd from Sumter, SC
- Parts Used:
- WR24X450
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Fresh Food Door Torn
My experience with PartSelect was excellent. My main concern was ordering the right gasket. First, I found the model number on the inside of the refrigerator. I ran model number on PartSelect and the compatible gasket came up. I removed old gasket carefully pulling it out. I cleaned around the groove that holds the gasket in and where the gasket lays. I boiled water and put it in a cake pan. I warmed up the gasket and smoothed and straighten it out. I started in each corner of the gasket and then worked from each corner pushing it carefully into the holding groove. Took me about 25-30 minutes. It seems to be working great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from east hanover, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
refig light did not work
per your instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert L. from Eldred, PA
- Parts Used:
- WR60X114
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Noisy fan
Emptied freezes, turned off power, took floor of freezer out [4 screws ], took two screws out of fan mounts and replaces fan. Reassembled by reverse process. Simple
Was this instruction helpful to you?
Thank you for voting!