ZFGP21HZJSS General Electric Refrigerator - Instructions

I put the water hoses out the valve and put the hoses back in new valve after that put the valve in the same place with the nutdriver. When refrigerator take the temperature inside, the ice began really easy. Thank you.

It just unpluged and the new one plugged in. Simple. The part was reasonable and arrived very quickly. It sure is nice to have a light in the frig again.

turn breaker off first then use thin blade screwdriver and plastic pry bar to remove light socket and switch there was plenty of wire so work was easy to install at both ends

replaced lights in refrigirator and freezer

Remove glass, lift cover up in front, slide out, transfer parts seals and switch for crisper(one pivot screw. Remove rear seal by using finger nail to pull at gasket slowly pulling it back. Take your time. Reinstall cover and glass, snap pivoting cover back on.

I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.

My GE SideBySide fridge stopped making ice. The green LED light on the icemaker was not blinking. The water dispenser worked fine. Fridge is only 5 years old. Freezer temp set at 7 degrees...fridge at 37 degrees. I have been using these temps since new. GE hotline suggested freezer temp should be at zero degrees. That did not work. Second call suggested an airflow issue within the freezer...there should be 1 inch space between food and back wall. Still no ice. The water valve looks to be the issue. I ordered it and got it in 2 days. Valve is in the back bottom, refridgerator side. Push the white collars around the water hoses...Then pull the hoses out. An adjustable wrench removes the nut for the inlet hose. Disconnect 2 electrical plugs. Be sure to push the water hoses fully into the new valve. I pulled the white collars out a bit to insure a tight fit. I was surprised at how simple this was to install. As it turns out, I was still getting no ice. I ordered a new ice maker and now I'm getting ice. The icemaker was EVEN EASIER to install.

removed the back cover, removed one srew that held the valve, disconnected water lines, and installed the new valve. Piece of cake!

I made my wife fix it.

Unplugged the fridge.
Took off the freezer door.
Took off the door brackets and the ice machine. Removed the back panel. Unplugging the light and the ice machine were a challenge to get to. Installation of the fan motor was simple. Reverse all the directions, done. Tough part was figuring out what to take off.

First I removed the ice tray rack lifting it out of the way to reach the back cover of the fan. Then, the whole back inside panel had to be removed. Two screws removed the fan and bracket from the freezer unit. The missing bumper lid just snapped into place. Replaced everything in reverse order. Pretty easy job.

Unplugged unit. Removed back cover plate. Used 5/16 water line. Cut old broken line. Used water tube union and attached new line. Removed electrical contacts. Note very easy removeand replace the red and white hookups. Next remove water line at the old vale with1/2 wrench. Hook up water line to new valve. Icemaker line was not damaged so I removed from old valve and trimmed the end. Really installed line to valve. Plugged in fridge and turned water supply back on. Check for leaks. Had trouble locatingthe 5/16 water line but found bulk. PARTS SELECT had the guest connector and the replacement valve. I received the correct parts and saved me $$$$. Plus my wife happy right before the holidays! !!,

Replaced Double Outlet Water Valve then defrosted coiled plastic water tubing at bottom position inside refrigerator into pan of hot water for 10 minutes. Water still did not flow. Defrosted refrigerator and water dispenser immediately resumed operation. Suggestion -
defrost refrigerator first.

First, turn off power - since I did not want to pull the refrigerator out on my wood floor I tripped the circuit breaker to that circuit and opened door to make sure interior light was off (ensuring power was off). This unit has a bottom freezer, I took out all shelves, ice maker and all parts in the way of accessing back of interior of freezer section. Removed back plastic section by removing one screw in middle top of back panel and prying it out. This was a bit difficult as it was in there a bit tight but once the plastic warmed up it pulled out ok. This revealed the compressor section and temp sensor that was attached to the copper coils with of all things - a zip tie! In pictures of this that I looked at on various web sites the sensor was on a metal bracket attached to the coil so it made me wonder if tf the factory took a shortcut? I cut the old sensor wire, stripped the two wires 1/2", and connected them to the new sensor wire with butt connectors, I put some silicone into the ends of the butt connectors to prevent moisture from entering into connectors and wrapped the connection in black electrical tape. I then "attached" the sensor to the coil using a zip tie, put the plastic back piece back on, inserted everything I took out and put power back to refrigerator. It's been 3 days and temp of refrigerator is stable, ice maker not clogging up, and compressor not running all the time! So far so good.

Very simple fix. Just remove the back cover, unscrew the water valve, unplug the water valve and disconnect the water line. Then reinstall the new one. Takes about 15 to 20 min and it worked like a champ