PSTW6YGXAGSS General Electric Refrigerator - Instructions

I think there were 3 philip screws to remove, take off the existing glide and replace with the new part. A very simple repair and saved about 175.00 if called in a professional, Thanks Part Select

Replaced the auger

The three bulbs would then remain on, so I loosened them to keep them off. I didn't know that the cooling system also would stop when the door was open, so for two days only the side freezer was operational. When I discovered that, I hot glued the switch button off, while I searched for a replacement part. The replacement part was an exact duplicate. A simple prying out of the old switch - using a screwdriver, and the reconnection of the two wires connectors to the new part, and clicking back in place ... done. Seriously, it took two minutes.

Looked it up on You Tube and basically followed the very simple instructions. Two minor differences: 1) I took the old gasket off while the door was still attached to the fridge. And 2) because it was a side-by-side freezer/ fresh food, I didn't have to take off the freezer door at all and the fresh food door was only attached at the top with 2 screws covered by a hinge cap. So I undid the screws and lifted it off the lower pin. We put the door on a table handle down and slightly off the table edge. Inserting the v-shaped rubber part of the gasket into the groove was easy- pinching it together with my fingers with a little hammer tap at the corners. Reinstalled the door and voila. 27 minutes!
Most of my DIY projects take twice as long as expected. Much time is spent taking off the old part then not as easy as expected to replace the new part. This was a breeze!

Handle just snaps on.

Removed broken switch with plastic scraper (press tension latch on bottom), moved two wire terminals to the new switch and pressed the new switch into the hole.

I ended up needing to order a new ice maker because the one I had is discontinued. I'm a 65yr old grandma and I did it myself!!!! The hardest part was finding the tool to loosed the nuts. I took the old one out and just put the new one right in it's place. Easy as pie.

Unplug refridge then loosened two bolts holding old ice maker. Lower then unplug and removed. Plugged in new harness and tightened two bolts to secure new ice maker. Plug in frig and wait for ice.

Pulled the fridge away from the wall. Unplugged. Turned water supply off. Removed the bottom panel. One screw and a small hook holds the assembly on. Remove clips from the solenoids. Disconnected the main water supply line. Pushed up and held the clamp ring and pulled the water/ice maker supply lines out. Replaced everything in reverse order. Simple fix!

My son did it , and showed me what he did when he was finished.

Amazingly simple. I followed the directions I found on your site 4 socket screws removed. They were easily accessible. Replaced the broken bucket guide with the new part. Put the screws back in in less than 15 minutes the icemaker auger feature that dispenses the ice was back in working order.

I had previously removed the motor by unplugging 2 plugs and had the motor sitting on my kitchen counter awaiting for the part from the site. On receipt of the part, we removed the broken left glide, installed the new glide, re plugged the motor and attached it to the new glide. If it weren't for my hubby trying to find the right socket tool for the screws, installation would have been less than 15 minutes. The screw that attaches the glide to the ice motor is a different size than the ones that screw into the side of the fridge.

removed broken bin , slid new ice bin in closed door. I bought the complete part.

I took out the old bins just as when you take them out to clean them. And then I replaced the bins with the new ones.

Simply take off the back panel. Remove the old run capacitor which is attached to the compressor by a white part. It pulls right off. You will have to unplug two wires. I took a pic to ensure I plugged the wires back up the correct way. Then I attached the new capacitor to the white part and put on the sleeve that was included, plugged it back into the compressor and zip tied the excess part of the sleeve. Once done plug fridge back up (always unplug electric devices when doing maintenance) to check before replacing back panel. It may take a few minutes before it kicks on.