ZISP420DHBSS General Electric Refrigerator - Instructions

The only tricky part was removing the front panel. Releasing the latches required considerable force. The best tool I found was a "jack knife" type Allen wrench set, using the medium size wrench, which fit into the release hole and upward pressure did the trick. The rest of the job was very easy.

We had problems with the ice dispenser chute building up frost from condensation freezing due to the flap not closing properly. It would clog up completely and often. I had already replaced the flap and spring years ago but it didn't help much. I Googled this problem for my model and found a video detailing how to check and change the solenoid. Sure enough, the solenoid was completely corroded and crumbled in my hands as I removed it. I ordered the replacement part and made the repair myself. The video was perfect in describing. If your refrigerator is well used as ours is, you'll be shocked by the buildup and cleaning that will be necessary as you make this repair. I ended up taking much more of the dispensing assembly apart so I could clean it with warm soapy bleach water. Be mindful as you disassemble or take photos / videos with your smartphone to help put it back together. It took longer to clean than replace the solenoid. Also, be careful if you have an island or other cabinetry close by. If you have to pull the refrigerator out to unplug it, the handles can chip granite edges or the top corners can scratch wood work. We have cherry cabinets that surround ours. I chipped the edge of the granite when I pulled it out and I scratched the wood as I pushed it back in place. Minor repairs but can save you some frustration. Good luck!

Fairly simple fix. You must first uplug refrigerator, then take off the inside freeze door panel, approx. 25 screws. Then you must take out the trap door assembly approx. 6 six screws. Pop off the LED panel, requires the use of a flat blade screw driver to pop it off. Remove solenold by removing 3 screws, replace with new solenold.

1. Remove outside panel (snaps off)
2. Remove Control panel 4 screws
3. Remove Solenoid by taking out 2 bottom screws
4. Remove solenoid weight from crank lever
5. Place new solenoid weight from crank lever
6. Insert weight in solenoid
7. Place back 2 bottom screws solenoid
8. Place back Control panel screws
9. Snap back into place outside panel

Researched on internet/you tube; ordered part, and did the repair. Easy to do and saved the cost of a service call.

Took the old filter out and put the new one in.
Easy Breezy!!

Replaced dispenser door flapper by following the do it yourself video in this site. It was really easy. Just be careful when removing the dispenser black bezel. I broke one of the little tabs when taking it off.

I followed they instructions from the other "do it your selfers" but only replaced the solenoid. This was the cause. Rust was keeping solenoid plunger from moving and this held the flapper door open. Very easy to repair!

I only had to remove the old filter and install the new one - all by hand. I then ran about 1 to 1and1/2 gallons of water through the filter to clear it.
A WORD OF CAUTION - HOLD YOUR GLASS CLOSE TO THE WATER DISPENSER FOR THE INITIAL FILLING - IT WILL SPIT UNTIL THE AIR IS PURGED FROM THE SYSTEM!!!
An extremely easy repair.

Replaced rusted solenoid.

Popped front button panel off from the bottom using flat head screwdriver; Removed 4 screws holding electronics board and disconnected wires. Unscrewed 3 phillips head screws on old solenoid and replaced with new part. Reconnected wires to board, screwed back in, and pushed panel back into to place.

Thumbs up to PartSelect - fast, straightforward service and fast delivery.

Pop off the control board for the ice selector/water. Remove power / signal connections. remove four phillips screws, Remove plastic hopper. Pop off Ice door gasket, pop in new one and put back together. If you fridge was sounding like it was speeding up and slowing down, this will correct this problem as well.

I removed the door cover plate and disconnected the circuit board, then four screws. The part was corroded in place. Upon removing three screws and cleaning the surface, the new part was an exact fit, replaced it and everything works like new.

repair was easy, just removed control panel and removed screws from solenoid, switched out with new, was done in minutes

Took old one out with my fingers. Put new one in with my fingers.

Remove control panel.
Remove four screw in control panel bracket.
Remove to bottom screws at bottom of solinid loose top screw.
Replace all screws.