GTRC0KBZALWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- rodney from cave city, AR
- Parts Used:
- WR60X10220, WR60X10207
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Socket set
warm in lower area and not freezing good in freezer area
condenser fan on bottom condenser not runningchanged fan and fan motor
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from York, PA
- Parts Used:
- WR60X10220, WR60X10207
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Freezer not cold, Frig cold enough, runs all the time, Hot to touch in spots.
My compressor fan that blows over the coils was not spinning. I measured 120 VAC going to the fan so I knew it should have been spinning but wasn't. Took fan motor out and took it apart and super lubed the motor to get it spinning again temporarily until I could get the new one in. Put new one in and has been working for about 10 days now. Freezer is not below 0 deg F which is what you want. Frig is below 40 deg F also what you want.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andenet from Haymarket, VA
- Parts Used:
- WR60X10220
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Fan and housing cannot be removed together.
On partselects video the gentleman removes the fan and housing in one piece. This is a great idea but does not work on this brand of ge. I removed the fan housing screw as instructed but left it in place and swiveled it enough to access the retaining screws with a socket driver. Over all swap of the fan was seamless and the video is a gem. Andy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from Seattle, WA
- Parts Used:
- WR60X30922
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver
broken fan blade
about an hour to figure out what was causing the vibration and noise and about an hour to put it back together and 5 min. to order a new fan blade thank you.It started making noise during thanksgiving dinner so we toke it apart after dinner and I cut the other 2 blade to match the broken one so to cut down on the noise and vibration semi put it back together and 7 days later the part arrived.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bryan from Las Vegas, NV
- Parts Used:
- WR60X10220
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
condenser fan was noisy ( squeaking)
Not knowing anything about a refrigerator it was hard to find the source of the noise. Once I could isolate it we googled the appliance repair and found the video from Parts Select and the rest was a piece of cake. Saved a service call and bloated parts prices. Thank you Parts Select!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Audie from Des Allemands, LA
- Parts Used:
- WR60X10220, WR60X10207
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Socket set, Wrench set
Fan not working. Fridge and Freezer not cool
It was simple. Unpluged fan two screws remove from fan bracket unplug old fan replace with new one put fan in place out screws back plugged in fan then plugged in fridge fixed problem. And save a repair cost call out. A.J.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Scott from Golden, CO
- Parts Used:
- WR60X10220, WR02X10098
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator over cooled, discovered condenser fan had failed.
Follow the directions on the video, removed the back panel, unplugged the existing fan, removed the fan assembly, installed the new motor and reassembled the components.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from east hanover, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
refig light did not work
per your instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Guojie from Gainesville, FL
- Parts Used:
- WR60X10220
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
noise from the condebser fan moter
Just follow the instructions from the Youtube, the link to the video is included in the sheet coming with the part. It was easy to take the entire compartment out as instructed, however, after replace the old motor with the new one, it took more than 20 min to put the entire compartment back after trying different ways. It has been working greatly since it was repaired.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- MICHAEL from Lubbock, TX
- Parts Used:
- WR60X10220
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Fan wasn't running and walls of freezer and ref. were hot
took screw that holds motor frame in place out with nutdriver, rolled motor frame out after unplugging motor,took screw out of strap that held motor in frame, removed bushings from old motor and put them on the new one and re3versed the proceedure.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from castle rock, CO
- Parts Used:
- WR60X10220
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Fan Sqeels
Remove back panel . Removed fan shroud. Replaced fan and panel. Ops ck ok so far
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joe from decatur, GA
- Parts Used:
- WR55X24064
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Freezer And Frig Both Warm And Compressor Would Not Run
I replaced the thermostat, temperature sensor, and the run capacitor. . . Refrigerator still not cooling. I checked the start relay and measured the input terminals on the compressor for the correct resistance. . . Everything measured correctly. In a last ditch effort before calling for service, I pulled the main board, inspected it and saw the problem right away. One leg on the compression capacitor had desoldered itself. Got out my soldering iron and applied a good amount of solder to that point. Put everything back together and turn it on. . . Problem fixed. The compressor kicked on right away and started cooling the refrigerator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANTHONY from NEW EGYPT, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
sticky switch
easy pry out, disconnect wiring, connect on new switch and press in switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from Durham, CA
- Parts Used:
- WR55X24064
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
compressor running and hot, refer and fridge room temp.
Watched a youtube on capacitors- though on a motor with a pulley, the symptoms were the same, motor running and pulley not turning-bad capacitor. Took a chance for a 17+ dollar part vs a new compressor. It worked.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JOSE from NEW YORK, NY
- Parts Used:
- WR55X24064
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
fan and compressor wont start
Googled the model number of refrigerator with symptoms of "refrigerator wont run". Parts select web site appeared on my screen, opened Parts Select website, Partselect said probable cause of my frige symptom was that the run capacitor usually burns out 51% of the time. They were correct with the diagnosis 100%. I ordered the run capacitor for $23.00, installed it in 10 minutes, refrigerator runs good as new. Thank you for saving me cost of service call. I probably saved $200 or more. I will use Partselect again with my next problem. THANK YOU,
Was this instruction helpful to you?
Thank you for voting!