GTH18GBDGRBB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Edith from WARRENTON, NC
- Parts Used:
- WR17X11911
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door shelf retainer bar broken.
Removed the old bar and slipped the new one in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THELMA from APOPKA, FL
- Parts Used:
- WR17X11911
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken
lifted old broken bar & replaced with new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J.Larry from TALLAHASSEE, FL
- Parts Used:
- WR17X11889
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
replaced a plastic shelf on the door
shelf just snapped into place. It was so simple, "even a caveman could do it."
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from BROOKLYN, NY
- Parts Used:
- WR17X11889
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Broken door shelf
Slipped it it-very easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ella from RODESSA, LA
- Parts Used:
- WR17X11890
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
None
Just place the shelf door bar in slot and push in place gentle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronnie from BATON ROUGE, LA
- Parts Used:
- WR82X10111
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
had no access cover on back
screwed the cover on just like the original
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from BRADLEYVILLE, MO
- Parts Used:
- WR23X37285
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Broken light switch
This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maureen from LYNCHBURG, VA
- Parts Used:
- WR60X31522
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Refigerator was amking a loud noise when the fan came on to cool.
Followed the on line instructions and found the repair to be very easy. Took longer to remove the food from the freezer than to switch out the fan motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from GREENSBORO, NC
- Parts Used:
- WR02X12008
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Fan was not centered in the middle of the back panel opening.
Bent the motor bracket down, then using a rat tail file, elongated the holes in the back panel of the refrigerator to secure the fan in the "centered" position. This was a problem that was with the refrig. since it was made. The parts involved were perfect. NO problem at all installing them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gilbert from LOUISVILLE, KY
- Parts Used:
- WR60X31522
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Evaporator motor bearings failing - squeaking
1. Watch the video.2.Place all screws in a central location that will not be hit, stepped on, fall on the floor, etc. 3. Be systematic. 4. Allow a full hour. 5. Watch the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from BOZEMAN, MT
- Parts Used:
- WR02X12008, WR02X10540
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Noisy Freezer Evaporator
Find a video on youtube. Remove 6 screws. Pull the Styrofoam part up before removing the panel. Unplug and Remove the fan assembly.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Randy from VALLEY CENTER, CA
- Parts Used:
- WR02X12008
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Loud whirling noises when the motor started up, then they subside (and stop) in a short time
I have not yet done the repair. After watching this repair video two problems came to mind. First I only ordered one grommet not knowing that there were two (or more I don't yet know). The second problem is that this video must be for a fridge from like the 1940, but it looks NOTHING like mine from 2008. The manual shows a bazillion parts and frankly I'm just a wee bit afraid to get started, and I am generally very handy, buuuttttttttt I don't know about this one
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from NEW YORK, NY
- Parts Used:
- WR02X10540
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
noisy refrigerator
I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendy m from BROWNINGTON, VT
- Parts Used:
- WR60X31522
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
freezer was too warm, only froze ice cubes on the bottom, fan making noise, food only stayed froze if already frozen
followed instructions in the video. simple tools. pretty easy. Most people would have just bought another refrigerator, $50.00 was much better. Is working just like new.
Was this instruction helpful to you?
Thank you for voting!