33346 General Electric Refrigerator - Instructions

Followed the video for this repair. Only issue was that the videos showed that when the front panel is removed, there is a wire harness that has to be unplugged from part No. 38c. This was not the case. What I had was a Ribbon Cable Harness that plugged into the front of part No. 38 and the top of part 38C (the two power boards) I tried to disconnect it from part 38C by pulling it out, and apparently damaged the Ribbon Cable Harness. Later found a video showing how to remove this item properly when replacing power boards 38 and 38C. Have ordered a new cable from GRP and hopefully this will solve the problem, as there is no electrical current to the dispenser controls and the ice and water dispenser are not currently working. Would have been nice to know that there are two types of connections between these power boards; a cable harness that unplugs from 38C or a Ribbon Cable Harness that unplugs from from the face of part No. 38. Hopefully I have not damaged either of the boards or anything else. Professional repair man coming on Thursday to test the boards, micro switches, etc. The boards are quite pricey, ($550.00 for both) and since the refrigerator was manufactured in 2004, we will buy a new one before we pump any more into this older unit. Very important to know how to unplug this Ribbon Cable Harness from the boards before proceeding ! Plug in on 38C is very tricky and you will need to review a video showing how it is done.

just followed the instructions

First I determined the icemaker was the problem when it was no longer calling for water. You can hear that "whistle" for 6-7 seconds when it calls for water. Anyway, replacement was a piece of cake, but did not entirely fix my problem. I also had to flush the lines to the soloniods that allow water to flow through the filter and into the water storage tank because it was cloggged with a little piece of plastic.

BOUGHT NEW ICEMAKER TOOK TWO SCREWS OUT, UNPLUGGED THE ELECTRICAL CONNECTION. REMOVED OLD ICEMAKER, PUT TWO SCREWS BACK INTO REFRIGERATOR(DON'T SCREW ALL THE WAY IN AS THE NEW ICE MAKER WILL FIT ON. HOOK ELECTRICAL CONNECTION AND ADAPTER (THAT COMES WITH IT). PUT THE DRAIN TUBE IN ITS SPOT, HOOK ICE MAKER ONTO THE TWO SCREWS TIGHTEN EM DOWN. I DID THIS RIGHT BEFORE I WENT TO A BIRTHDAY DINNER WITH MY HUSBAND, WAS ALREADY DRESSED AND READY TO GO AND I TOLD HIM ILL PUT IT IN SO WE CAN HAVE ICE WHEN WE RETURN. ENDED UP BEING A SURPRISE PARTY FOR ME AND WHEN WE RETURNED WE HAD ICE. IT WAS SO EASY EVEN A GIRL CAN DO IT!!

followed instructions on your video.. PERFECT and easy.

I followed the instructions on your website, made it a simple as possible. Very tight work area sometimes fingers only, but a little patience works.
Saved at least $300. By not paying a repair person.

After determining the ice maker was getting water but not harvesting the ice, I ordered a replacement Ice Maker. Installation was easy. One electrical connection and two screws. Following the video to make sure I did not miss any steps I had ice in just a few hours. Just in time for a July heat wave!

Unscrewed (loosen) screws lifted unit out unplugged electrical connection. plugged in unit hung on screws tightened screws and had ice in less then 1 hour. Rick

plug and play. removed old one, and install new one.

Removed water tray, removed 3 screws (a little rusted), took off cover, removed 3 more screws, unpluged wiring, removed screws holding in actuator, removed broken part, installed new part making sure spring was in the right place. Put back together.

Had to replace with a whole new part, had to take it all apart to replace

Loosen two screws, unplug power, lift it off, put new one on and make sure water chute is correct place, tighten screws!

This was the last step of serial repairs to the ice crusher portion of the ice maker. I have practically replaced the entire assembly. All the blades were installed incorrectly (at factory? Afterwards?) and had bent. That caused problems for other parts. I hadn't noticed that the housing was weakened and my prior repair I did something dumb and the door on housing wasn't closing properly, so it snapped. I bought a new housing and installed it. My #1 tip is WATCH THE VIDEO! There are some things that have to be put together just so. You need things to line up and be under slight tension from springs. Last time I had it under too much tension. The door got in the way of the blades and broke. So this time I was more careful to do it correctly. Everything is working perfectly now. This design is clever, and I feel like I can diagnose and fix it again in future. "Steve's" instructional videos are a huge help. He shows exactly what to do.

We had someone to come and look at it and we were told it was the solenoid valve. The repairman unstuck it for us and said when it does it again, he would have to order the part. We took it upon ourselves to order the part and DIY. We replaced the part that we were told was the problem and "guess what" it's still not fixed. It's still shooting out crushed ice. Will have to call repair guy back out here to see what we did wrong.

watched the video (VERY helpful) and then removed the old icemaker and replaced it with the new one. Difficult only because of the small working space in the side by side freezer plus you can't see what you're doing when you tighten the screws. Working like a charm now.