PNQ22LMHBFES General Electric Refrigerator - Instructions

simply read the instructions

it was easy. Open the fridge,untwist the old filter. Open the new filter, fill with tap water and twist in place. Run water through it for a few minutes to insure it is working and filters the water.

After confirming that a frozen water line was not my issue, I confidently bought this item and installed it within minutes after receiving it! It is easy to install - just close the connection to your refrigerator, open the rear lower panel, disconnect the water tubings and electrical connectors. Reverse that - you have the installation. Plug the refrigerator back on, turn the water back on for the refrigerator - and observe for any leaks. If no leaks - try dispensing water. Working great for me! My refrigerator's model is a GE, model # zfsb26dnass.

It was as simple as taking off back panel and disconnecting 3 tubes and and two plugs to remove old valve and attaching the new valve piece to the 3 tubes and two plugs! It actually took more time getting the panel off than making the repair AND it saved us a little over $300 as the repairman quoted a price in excess of $350 to repair it. He was actually the one to tell us to buy the part ourselves and repair it. We are thankful being able to get the part and for an honest repairman.

turn off water remove back cover remove 1 screw holding water valve use wrench to remove main water line input push up holders on bottom of selinoids pull both output lines loose disconnect two electrical plugs reinstall new valve in reverse order

PartSelect helped me identify the part, got it in only a few days and I followed the easy to follow video featuring Steve. Awesome!

I was unplug the electrical,closed the water line.replaced old water outlet with the new one;and there work fine.Thanks

I turned the water off at wall. Then I removed 6 nuts removing the back cover. Removed one nut to remove the outlet water valve. Disconnected two bottom hoses and put them on the new unit. Removed top hose and installed on new unit.
When I removed the top hose water did spill out.
I had to rush to connect it to the new unit .

Easy repair. Diagnosis was tricky - this website and popular mechanics article helped me to narrow down the problem to the solenoid water valve.
Unscrewed the left side of the back panel and unscrewed old water valve from its bracket. The steel inlet hose was easy to disconnect, as were the two electrical socket connectors. The two outlet water hoses to the refrigerator were a little trickier. You need to cut them with a blade, and insert them into the new valve, which has teeth to hold them in place. Once I figured that out, the rest was easy. I remounted the bracket, and then tested the water flow successfully. Great website, thanks for the help!

Removed back lower panel, removed valve, ordered part on internet, cleaned motor and back of fridge. Most time spent was waiting for delivery of ordered part. Part received and installed in 15 minutes after reviewing instructional video included in my email verifying my order, fridge pushed back into place, waited for ice maker to refill.....DONE. So easy. Thanks guys. Job well done.

After gaining access to the back of the refrigerator. I shut off the water valve and pulled the electrical power plug. I removed 6 screws from the access panel. I then removed 1 screw holding the water valve. I disconnected the electrical connectors. Disconnected the water inlet tubing with an adjustable wrench. I removed the water to the door and water to the ice maker by pushing in on the collar which released the tubing. I discarded the old valve and installed it in reverse order. Did not fix the problem. My next guess is the control module.

Unscrew the mounting screw and cut the tubes as close as you can to the valve. You cannot reuse the valve as the self sealing lock washers will be destroyed once you take out the tubes. Push the newly cut tubes into the new self sealing new valves and remount. Easy Peasy!

pullee refrigerator out to get to back un pluged power took off back cover unscrewed one screw to loosen water valve unscrew water inlet line ther are two water lines in back of water valve i cut them as close to water valve as i could push the water lines that i cut off into water valve makin sure in the rigfht place they are quick disquinect just push in and ther on screwed water valve back on connected water inlet line replaced back cover pluged in power pushed refrigerator back in and was done it had to run for a little while to get the air out then worked fine

removed rear cover of Frig, found valve was cracked and leaking water. turned off water and ordered new valve. After receiving new valve, Removal and installation took about 15 minutes. Pretty easy, a no brainer.

Unplugged fridge, and turned off water supply. Removed cover from back of fridge, followed the plastic tube down to water valve.
I unbolted the mount holding water valve in place, removed the input tubing on top by unscrewing nut. I made a note of which outbound plastic tubing went to water dispenser, and which one went to icemaker, and which side of the water valve they plugged into, and then cut the tubing very close to the old valve.
I slid the tubing into the new water valve, and I felt it lock into place, very easy. Attached the input water line and tightened the nut.
Reattached the water valve mount to the body of the fridge, replaced cover, turned water valve back on and checked for leaks (there were none).
Plugged in fridge, tested dispenser, everything worked just fine. No leaks.