CFRP5NFDASS General Electric Refrigerator - Instructions

Moved stuff out of my way on the top shelf, reached in and turned old filter to remove. Filled new filter with water, lined up and turned to lock in place. Whew, never thought I would get that job done. :-)

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.

Turned the wire protector to the side. Turned out the old bulb and replaced it with the new. Turned the wire protector back in place and I'm like new.

installed the new door shelf

Simply clipped the new handle onto the pullout tray. GE has simplified the design of the replacement easier to install. Shipment of replacement was quick and excellent customer service.

Took the old filter out and put the new one in.
Easy Breezy!!

1- youtubed the potential diagnoses, 2- resourced and ordered parts, 3- removed old socket, installed new one :-)... My fridge is an older fridge and could've used a screwdriver for eyeglasses. Plug and play easy... YAY!

I only had to remove the old filter and install the new one - all by hand. I then ran about 1 to 1and1/2 gallons of water through the filter to clear it.
A WORD OF CAUTION - HOLD YOUR GLASS CLOSE TO THE WATER DISPENSER FOR THE INITIAL FILLING - IT WILL SPIT UNTIL THE AIR IS PURGED FROM THE SYSTEM!!!
An extremely easy repair.

1.Google troubleshooting for this issue. Determine the inverter card was bad. Installed new card and correct jumper harness per instructions. Total time to troubleshoot, remove & replace was about 30_45 min. Pretty simple

I ordered the part, within two days we had received it. My husband put the part in and I really don't know what he used doing so. All I know is that the light works now and we don't have to use the flashlight. Thanks a lot.

put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil

This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!

WE (WIFE) took out the old parts an replaced with new one ..Be careful to get the placement of the Grommet or they "POP" out on you. fast ship on the parts too.

The best instructions were several YouTube videos for replacing icemakers on GE french door bottom freezer refrigerators, but none fully described the process. The following difficulties were encountered: (1) Instructions for removing the freezer door showed three screws on each side that needed to be removed; in fact, there was only one screw on each side. It was smaller than the three depicted screws and its location was not exactly as shown in the videos. (2) None of the instructions adequately described the process for removing the mounting plate from the nonfunctioning icemaker so it could be attached to the replacement unit. The key was to forcibly pry open the cover over a screw that then needed to be loosened with a screw driver. It seemed that I risked breaking the unit when I tried to slide the tab, but it eventually moved and revealed the screw that was holding the original mounting plate in place. (3) Replacing the freezer door required lining up some metal studs with slots in the undercarriage; you need to get down on the floor to examine how this fits back together. (It might help to take some photos before removing the freezer door.) (4) Replacing the upper drawer was perhaps the trickiest. My first effort resulted in having the rod with gear pinions on each end pop out because some of the tabs holding the gear pinions on each end broke. That meant that I had to order two replacement gear pinions (left and right are identical). Then, as with the freezer door, it was necessary fo slide metal studs on each side into a vertical slot leading to a horizontal slot in order to seat the upper drawer properly. So the whole process took a few weeks; actual work time was perhaps 3-4 hours. This could have been shortened significantly had I taken photos as I disassembled everything and if the procedure for moving the mounting plate had been clearer (or even existing). All in all, though, this is a doable DIY project.

Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch dislodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.