PNR22LSEBFES General Electric Refrigerator - Instructions

I found that the valve was not the problem. Check to make sure you do not have a frozen water line as I did.

changed outlet valve.not the problem.needed a new filter valve assembly.

Easy job except for moving the Refigerator but it is on rollers but it is still heavy. Unplug the Ref and shut off the water and replace the valve and the reverse the order. Simple

shut off water supply behind refrigerator, opend line at double outlet water valve. had water there. opend line at bottom of freezer door. no water there when I pushed watervalve on door. replaced double outlet water valve. then had water at hose at bottom of freezer door. but no water at outlet. took hair dryer and heated freezer door until ice melted in hose . then everything worked fine.

Changed out the double outlet valve which was pretty easy, after getting the right one, had the wrong part number for the first valve, not PartSelects fault, but still no water.Before changing valve, ice maker stopped making ice, figured the valve went bad on both points. After changing valve, got ice but still no water.Now what? Pulled the front cover off the freezer door where you get ice and water and found the bracket, } that holds the micro switch that works the water valve broken and the switch dangling. I screwed the switch back to the spacer between it and the frame and glued the spacer to the frame with plastic crazy glue.Got water!

-unplugged the refrigerator
-replaced water filter inside refrigerator
-turned off water suppy at valve
-unscrewed tin cover on lower part of refrig
-took brace off that holds the double water valve
-disconnected water lines and caught excess water in a bucket
-pulled out both electrical plugs out of old dual pump
-blew out with air the black water line that runs diagonally from the part to the top of refrig going into ice make(to make sure not clogged)
- Installed the new part and reconnected all of the above.
plugged in the refrigerator
opened the valve to let water flow inot refrigerator.
done--but still no ice cubes? HELP!

Rolled the fridge away from the wall, unplugged the unit from the wall outlet, and removed the back panel by taking out the 6 1/4" nuts that held it in place. Vacuumed the dirt and dust out, and sneezed viscously for 2 minutes. Removed the 3/16th nut holding the water relay. removed the inlet water line, and quickly replaced it. dried off, then went down stairs and turned off the saddle valve. mopped up the water, then removed the water inlet valve. Removed the 2 water lines to the unit (Ice and water feeds) and removed the 2 wire connectors. reversed the process in installation, except the drying myself off part, and sneezing from the dust and dirt.

Replacing the water valve was easy - the video was excellent. However, the problem was not solved - no water even after replacing the water valve. Anyone have any other thoughts?

It went exactly like the repair video showed. I removed the back cover, unhooked the water lines, unplugged the electric connections, and replaced the valve. That video made it super easy and it is now working like it should.

Just turn the cartilage out and put the new one. Very simple

pluged the wire harness into the new socket from the back and snaped the socket in place.

it was easy. Open the fridge,untwist the old filter. Open the new filter, fill with tap water and twist in place. Run water through it for a few minutes to insure it is working and filters the water.

1. Turned off water near hot water tank 2. Removed back (small section) of the refrigerator, only 7-8 screws. 3. Disconnected the old water hose (comes out easily. 4. Reconnected new water valve 5. Turned on water @ hot water tank 6. Replaced back of refrigerator. All done! I have never done anything like this, and I had no instructions, very easy to figure out. The part cost $48 here.

simply read the instructions

Simple repair. I first shut off the water supply to the unit. I then removed back cover from lower part of the unit. The water valve is on the lower left side. I began by removing the screw on the bracket that holds the part in place. This screws into the back of the unit. I then disconnect the water line by unscrewing the fitting. Then unplugged the two electrical connections in the back of the unit. Lastly, remove the two hoses that plug into the bottom of the the unit. The installation was essentially the reverse of the the removal. The whole process took about ten minutes.