PIR23MGTABV General Electric Refrigerator - Instructions

removed the back cover, removed one srew that held the valve, disconnected water lines, and installed the new valve. Piece of cake!

My GE SideBySide fridge stopped making ice. The green LED light on the icemaker was not blinking. The water dispenser worked fine. Fridge is only 5 years old. Freezer temp set at 7 degrees...fridge at 37 degrees. I have been using these temps since new. GE hotline suggested freezer temp should be at zero degrees. That did not work. Second call suggested an airflow issue within the freezer...there should be 1 inch space between food and back wall. Still no ice. The water valve looks to be the issue. I ordered it and got it in 2 days. Valve is in the back bottom, refridgerator side. Push the white collars around the water hoses...Then pull the hoses out. An adjustable wrench removes the nut for the inlet hose. Disconnect 2 electrical plugs. Be sure to push the water hoses fully into the new valve. I pulled the white collars out a bit to insure a tight fit. I was surprised at how simple this was to install. As it turns out, I was still getting no ice. I ordered a new ice maker and now I'm getting ice. The icemaker was EVEN EASIER to install.

I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.

remove light cover then remove 4 screws holding light fixture in place pulled out fresh food inlet cover and had to removed 2 more screws at bottom of cover then unplug electrical connector. replace with new one then replace all 6 screws and light cover done. so far its been working great no more freeze ups.

Turn-off water and disconnect main water line to inlet-tube.
Removed lower-back panel of the fridge with a screw driver and disconnected the hose with a small wrench to the main fridge water valve.

On th top-left, back of the fridge, removed screws to the small plate where the hoses enter for the water filter. In the fridge, removed the water filter, then removed the plastic panel above the filter - it snaps out. There are two screws to remove, then grasp and pull the assembly and hoses out. reverse the process for an easy install.

I was not able to put the small plate onthe back, top-left of the fridge back on. It's a tight fit and I didn't want to pinch the lines. Not doing that, though, may limit how your fridge rolls back to where it was, because the lines will stick-out a couple of inches.

I had to take off the back lower grate which was roughly six 1/4 screws. Disconnect the water lines to the ice maker and the filter manifold. Remove the manifold from the inside of the refrigerator by removing two 1/4” screws. Pull the manifold and line out from the inside of the refrigerator and reverse the process for the replacement.

I removed the cover on the back of the freezer side of refrigerator to expose the anti freeze element use the hair blow dryer to melt the ice on the coils put 2 towels to colect the water thats wath take me time, to replace the heath element was a 1 minute job.

replaced the water filter head and water lines which were fairly easy. Glad Partselect had was I was looking for and it arrived quickly.

I replaced defrost sets, door gasket but still ice buildup freezer part.

Replaced Double Outlet Water Valve then defrosted coiled plastic water tubing at bottom position inside refrigerator into pan of hot water for 10 minutes. Water still did not flow. Defrosted refrigerator and water dispenser immediately resumed operation. Suggestion -
defrost refrigerator first.

Replacing was easy. Cleaning took the longest. Order screws with parts, I could not find them at the hardware store. I suggest a coat of oil (3 in one) on the solenoid/piston surfaces. I probably did not have to replace them. The rust was inhibiting the piston movement. Some steel wool and oil would have probably fixed it. If the flap closing starts sounding softer, I'm going to take it apart and clean it first.

Unplugged unit. Removed back cover plate. Used 5/16 water line. Cut old broken line. Used water tube union and attached new line. Removed electrical contacts. Note very easy removeand replace the red and white hookups. Next remove water line at the old vale with1/2 wrench. Hook up water line to new valve. Icemaker line was not damaged so I removed from old valve and trimmed the end. Really installed line to valve. Plugged in fridge and turned water supply back on. Check for leaks. Had trouble locatingthe 5/16 water line but found bulk. PARTS SELECT had the guest connector and the replacement valve. I received the correct parts and saved me $$$$. Plus my wife happy right before the holidays! !!,

First, turn off power - since I did not want to pull the refrigerator out on my wood floor I tripped the circuit breaker to that circuit and opened door to make sure interior light was off (ensuring power was off). This unit has a bottom freezer, I took out all shelves, ice maker and all parts in the way of accessing back of interior of freezer section. Removed back plastic section by removing one screw in middle top of back panel and prying it out. This was a bit difficult as it was in there a bit tight but once the plastic warmed up it pulled out ok. This revealed the compressor section and temp sensor that was attached to the copper coils with of all things - a zip tie! In pictures of this that I looked at on various web sites the sensor was on a metal bracket attached to the coil so it made me wonder if tf the factory took a shortcut? I cut the old sensor wire, stripped the two wires 1/2", and connected them to the new sensor wire with butt connectors, I put some silicone into the ends of the butt connectors to prevent moisture from entering into connectors and wrapped the connection in black electrical tape. I then "attached" the sensor to the coil using a zip tie, put the plastic back piece back on, inserted everything I took out and put power back to refrigerator. It's been 3 days and temp of refrigerator is stable, ice maker not clogging up, and compressor not running all the time! So far so good.

Defrost heater turned black. Test showed infinite resistance. Problem went away after the heater was replaced.

Went on this site, found out many others like me had the flap door stuck open problem, it would not shut after you went for ice. I needed a new solenoid that opens when the ice is dispenced and closes afterwards not allowing the warm ambient air to come up the shoot which frosts the ice and melts it. It shipped QUICK and now I have a working ice maker dispenser from the outside. Its been 2 YEARS of opening the door and reaching into the ice maker bin for ice! Thanks PartSelect