PFSF0MFZJWW General Electric Refrigerator - Instructions

I found instructions on the web about how to do this repair, so I ordered the part with confidence. But the instructions simply said "pull out the old switchlight". That was actually somewhat difficult as the clip on the side intended to hold the part in was stubborn. I eventually used a utility to slice off the clip. From that point, it was just a matter of plugging in the new switchlight , which was very simple.

I made my wife fix it.

I replaced the water line and the inlet water valve

Checked water inlet tube inside freezer, stuck screwdriver in it to see if there was any ice and it seemed clear. Checked water pressure to fill valve, good pressure. Replaced fill valve, still no water to ice maker. Replaced Ice Maker. Still no water to Ice Maker. Removed freezer back panel, hit fill tube with heat gun after allowing freezer to defrost awhile, replaced back panel, ice maker. Water going to icemaker fine. Problem was that the fill tube was frozen up way at the back where the water line emptys into the icemaker fill tube. Old icemaker and fill valve were probably OK. No real way to check it from outside the case in the rear of the fridge as the water line is sealed on the fill tube and heating it without removing the rear freezer panel does not get back far enough to melt the ice.

No water flow after installation, part sent GSWF filter made in Taiwan had different treading then filter made in USA. Tried 3 from Taiwan same result. Found 1 from USA worked perfect.

replaced lights in refrigirator and freezer

Installing the part repaired the fridge and freezer immediately.

my freezer quit freezing, it would freeze for one day, thaw the next, so I went online, found PARTS SELECT, LOOKED UP MY MODEL #, come to find out it needed three parts to keep my freezer to freeze, first part was a thermistor a small PART took me longer to remove all the covers, and shelving, PULLED THE OLD OUT, CUT THE WIERS TO SIZE, AND REINSTALLED, IT WELL! THAT WASN'T ENOUGH THE FREEZER STILL DIDN'T FREEZE IT THOUT IT WAS A COOL WORMING OVEN, HAD TO INSTALL THE THERMISTOR I, SO I DID, TEN MIN, NOW I THOUGHT THAT WAS IT BECAUSE IT STAYED FROZEN FOR A WEAK, HAVE YOU EVER EATEN SOUPY ICE CREAM? SO BACK TO PARTS SELECT, THIS TIME I BOUGHT ONE MORE PT, THE RUN CAPACITOR, FIVE MIN, THAT/S ALL IT TOOK TO INSTALL. I DID NOT KNOW AT THE TIME YOU NEED THE THREE OF THEM TO RUN THE FREEZER ONE TO KEEP THE TEMP., ONE TO KEEP THE FAN RUNNING THE WAY IT SHOULD, AND THE THIRD TO MAKE SURE THE OTHER TWO KEEP RUNNING. NOW I CAN SET IT AT 4- 5 AND. FREEZE.

turn breaker off first then use thin blade screwdriver and plastic pry bar to remove light socket and switch there was plenty of wire so work was easy to install at both ends

The overload protector was the problem. It plugs into the side of the compressor and the run capacitor plugs into it.

If you pull the overload protector and it rattles when you shake it, that's probably your diagnosis.

The replacement is different from the original and the wire connectors are different. Hold the thing in the same orientation as if it were plugged in. The vertical connector goes to the neutral wire, which on my fridge is orange. The horizontal connector is for the overload, which for mine is black and white. If you have a schematic you should verify the wires yourself.

Anyway, the refrigerator now works like new.

It just unpluged and the new one plugged in. Simple. The part was reasonable and arrived very quickly. It sure is nice to have a light in the frig again.

I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.

Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.

Removed 2 screws and removed the old slide. Installed new slide and 2 screws . Done.

First I removed the ice tray rack lifting it out of the way to reach the back cover of the fan. Then, the whole back inside panel had to be removed. Two screws removed the fan and bracket from the freezer unit. The missing bumper lid just snapped into place. Replaced everything in reverse order. Pretty easy job.