CTS16ABMBRWW General Electric Refrigerator - Instructions

I had lost the bottom hinge during a move and so I rigged the hinge using an old tv antenna and the door never really quite worked right and it was VERY annoying. I stumbled upon this site and was surprised how inexpensive the part I needed was. I was very impressed with the speed of shipping and the install took maybe 5 minutes. The fridge works as good as new. Thanks a ton!

Removed freezer bottom and back plates-encountered ice -melted with heat gun.Observed fan not running with fridge plugged in and considerable erosion of the styrofoam part.ordered fan motor and blade and styrofoam ducting and replaced same.Fan started running immediately when plugged in and now the compressor cycles normally and the refrigerator compartment is much cooler and icing has stopped. I'm good to go until the compressor fails! thanks for the excellent delivery service(2 days)and your parts diagrams really helped me trouble shoot the problem.

It has been my experience that these motors sometimes die when the refrigerator is overfilled and motor strains to keep refrigerator cold. And this motor is used in several models of refrigerators. That said, sometimes the hook-up is slightly different between other units. The available video is good, but like I said, circumstances will be slightly different between various models.

After cleaning out freezer (plug disconnected first), start to remove outer plastic covers. If you want to keep track of the different steps, you can take pictures with your cellphone. And if there are any connecting wire attachments you think you might not remember, again, you can take a picture, or label with tape (colored tape, or by writing on the tape). And for keeping track of the different-size screws, I place them in a muffin tin, keeping an order of left to right and top to bottom in the tin. When removing Styrofoam blocks in bottom center, make sure you remove any remaining ice underneath in the hole so refrigerator can "breathe". Freezer air is moved below to refrigerator compartment, so a blocked vent hole will strain refrigerator as it tries to maintain its temperature setting and can be the cause of your failed motor.

After replacing motor onto bracket with grommets and blade, don't completely tighten. Position plastic cover with hole opening over motor and blade assembly. Twirl motor blade to see if there is any interference with cover. If not, take away cover and tighten motor on bracket. If there is any rubbing, adjust motor/blade assembly accordingly before tightening in place. Putting everything back together is in reverse order.

Easy fix - snapped together.

Followed the instructions on the repair video and it made very easy. Also saved us a lot of money. Thanks for your help.

Despite attempts to quiet the 2 year old fan, I went ahead and replaced it. Part Select was prompt with a new one at my door less than 24 hours. It was just the fan motor, so took a couple extra steps to place it in the metal housing, but no problems and though the frig still makes noises, it's not coming from the fan as before.

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

I haven’t received the wheel yet. Originally ordered on Dec. 13. Hadn’t received it by Dec. 20. Finally shipped on Dec. 22. Tracking said it was expected to be delivered on Jan.2. Not delivered. Then it said it was still on its way but it was unknown when it would be delivered. Still waiting on Jan. 6. By far the most expensive economy shipping ever, as this refrigerator is in a rental that can’t be rented until a wheel is installed.

First I removed the two screws, the fan and unpluged the electrical connection. Then, plugged in the new part and then screw it back together.

Took back out of freezer compartment, pulled plug and removed old motor, inserted new parts. It was
easy and the parts arrived the day after I ordered
online, even though I chose the cheapest shipping
option. Nothing in my freezer had a chance to thaw
out.

Shelf cracked when less than year old. and has gotten progressively worse thru the years.
Replaced in seconds , no tools required .
I should have done this years ago

The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around. If i had ordered the replacement before and not afterwards I would have seen this before hand.

My wife had the cover changed before I got home from work. Perfect fit for a replacement part!

After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.

The parts came the next day after ordering and I didn't pay for fast shipping. I removed the drawers and the old lid-shelf and replaced it with the new one; also added an extra shelf. I love the new items and they fit perfectly.