38080-2 General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- QUOC-LOC from LYNN HAVEN, FL
- Parts Used:
- WR55X24064
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
The control board generated clicking noise. Temperature display wrong values.
On the internet forum I read that if the control board needs to be changed , do the same for the Run Capacitor/relay.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
The Ge profile refrigerator was 15 years old. First I disconnect the power cord,
I removed the control board at the back of the fridge, replaced it with a new one and did the same for the run capacitor.
Plugged the power cord back and it works fine. GE repair service did not want to come to do it. DIY is fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ED from ENON, OH
- Parts Used:
- WR2X9391
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Short in the light socket.
Un Plugged the frig. Unlocked the socket by pressing down on the latch. Pulled the socket out ensuring I had enough slack. Unplugged the old socket installed the new. Plugged the frig back in. Tested the switch . Very easy-to-use.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nan from PURCELLVILLE, VA
- Parts Used:
- WR2X9391
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
My light in the refrigerator was going on and off.
I unplugged the refrigerator. Pressed the tab near the light bulb. Unplugged the socket and reconnected it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from SAN DIEGO, CA
- Parts Used:
- WR2X9162
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
My freezer door had a retainer bar that became disconnected at one end because the coupling broke.
I slipped the coupling over the bar and then into a door slot. It was very easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marj from NEWBURY PARK, CA
- Parts Used:
- WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fridge light dead even with new bulb
1- youtubed the potential diagnoses, 2- resourced and ordered parts, 3- removed old socket, installed new one :-)... My fridge is an older fridge and could've used a screwdriver for eyeglasses. Plug and play easy... YAY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Erika from Joliet, IL
- Parts Used:
- WR2X9296
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door shelf clip had broken
This shelf has been broken for about a year now and my husband tried several little quick fixes that would work for a while and then the shelf would fall again. A quick search online led me to your website, the part arrive within two days, and the shelf was fixed in less than ten minutes. It's working great. We'll definitely keep you in mind for the future.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stan from Dallas, TX
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken door shelf bar holder
I ordered the part before noon and I they had it out the door and in my hands within 24 hours! It took about 2 minutes to take out the broken part and snap in the new one!Great service and easy install!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Charlotte, NC
- Parts Used:
- WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
socket had melted
pluged the wire harness into the new socket from the back and snaped the socket in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Miranda from Waterford, CT
- Parts Used:
- WR2X9296
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The end cap on the door shelf snapped off.
I pulled off the broken piece, ordered the new piece, and snapped it on. VERY SIMPLE.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wayne from Issaquah, WA
- Parts Used:
- WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Light socket missing in refrigerator
Frig parts had been scavenged in an apartment complex. Restoring socket was only a matter of plugging in two spade contacts and clipping in socket.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sheryl from Wyoming, MI
- Parts Used:
- WR2X9296
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
door shelf retainer broke off
First, I removed the broken end cap from refrigerator door. Then I snapped the new end cap into place. Repair took less than 5 minutes and required NO TOOLS! Easy!! Got my part in one day, Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John D from Chevy Chase, MD
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
This part broke for whatever reason, I do not know.
I needed a pliers to extract the shelf reatainer from its place in the door of the fridge.
I found the part in the partSelect catalog, ordered it, opened the box, and snapped the replacement part into place. I then popped the Shelf retainer back into place where it belonged.
Piece of cake.
I found the part in the partSelect catalog, ordered it, opened the box, and snapped the replacement part into place. I then popped the Shelf retainer back into place where it belonged.
Piece of cake.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Clayton, NY
- Parts Used:
- WR2X9296
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The retainer latch broke
Removed the shelf retainer and snapped the new one in. and reinstalled the shelf on the door.
This was a very simple problem!
What really impressed me was that I ordered the part from you before noon on one day and received it by 11 AM the next day!!!
This was a very simple problem!
What really impressed me was that I ordered the part from you before noon on one day and received it by 11 AM the next day!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from Prescott, AZ
- Parts Used:
- WR2X8345
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken door shelf retainer
Just replace end cap and install. The beauty of this was the door was broken in the evening before July 4 when all retail had closed down early for the 4th weekend. I hit Part Select on the computer, scrolled down the partslist,looked at pictures and figured out from that the necessary piece I needed, hit the buy button and in less than 10 minutes had an order placed. July 7 UPS was at the door with the parts and my reefer was back in business. NO service call and no extra charges!!! Thank You, PartSelect!!!!
Was this instruction helpful to you?
Thank you for voting!