CFCP1RKBESS General Electric Refrigerator - Instructions

I watched the instructional video on this website and did everything that it said. There is no more leak when I use the in door water. Was as easy as it looks in the video and I am very happy!

I followed the video provided, and followed the advice of bill from cleveland hts. ohio, and did not have to remove the trim to access everything. The video made it so simple, a monkey could have learned how in 5 minutes. Thank you very much for all the help on this website. I will recommend it to all.

changed outlet valve.not the problem.needed a new filter valve assembly.

I followed the instructions posted by previous custmers and they were accurate and simple

I found that the valve was not the problem. Check to make sure you do not have a frozen water line as I did.

Had the wife shut the water off, while I was on vacation. Came home pulled the refrigerator out. Had an issue earlier in the year with a leaking hose. Discovered the valve had many pin holes and was going to need to be replaced. Went on line to Partselect ordered on Saturday. It was easy to determine if I had the right part. Purchased and received on the following Tuesday. 30 minuted later the refrigerator was back up and running with ice and cold water. Have used Partselect before always a great experience

Followed the on line video. Clear, concise & easy. Thanks.

I searched the site, found the part - solenoid, watched the "how to" video and the repair was a snap. Saved myself tons of money versus having a repair person come over. I do have an older model and needed to prop the front cover panel off with a screwdriver (just under the covering) saw this on a posting from another individual, thanks for the heads up.

I read instructions in all of the other repair stories everything went smooth no problems. Went and examined freezer door too see which type of door I had front or rear access. Popped off front LED panel, unpluged wires, removed 4 screws holding ice chute, removed 3 screws holding solenoid, slipped off solenoid pin, replaced all items in reverse order. This is one great site.

We didn't think the dispenser problem was related to the filter - we were wrong! It took less than two minutes, including opening the box and unwrapping the filter. I'll definitely be changing my filter more often - and buying it through PartSelect. Your ordering was so easy and delivery was unbelievably fast!

Easy job except for moving the Refigerator but it is on rollers but it is still heavy. Unplug the Ref and shut off the water and replace the valve and the reverse the order. Simple

We followed the instructions we found on this site.

First we unplugged the refrigerator.

Then we removed the control panel that has the ice type selection on it by releasing the three spring latches. These are accessible from the bottom of the panel looking up toward the ice dispenser. There are three holes. Press a narrow screwdriver or punch in each of these holes and then pull out the control panel. (Be careful not to disconnect the wires, but observe how the wires are routed.)

Then we removed the ice tube cover that covers the solenoid assembly. There were four screws. One was very rusty and it required some WD40 to loosen it. Once the cover was removed the solenoid was visible on the right. (It has a floating component that attaches to the "arm" of the flap. This is how the solenoid opens and closes the flap. The flap needs to close properly so ice does not build up in the door.)

There were three screws that had to be removed to get the solenoid out. (The top one you may just need to loosen once the bottom two are removed.) When the solenoid was removed we also removed the old floating component from the flap are and replace it with the new one. We slid this into the solenoid hole and then screw it in with the three screws.

Before we attached everything, we plugged in the refrigerator to test the solenoid. We dispensed some ice and waited to hear the flap close. (The flap close is slightly delayed so be patient.)

We attached the cover that was over the solenoid being careful to route the wires as they were when we started. We test the solenoid again. Then we snapped the control panel back into place and tested again.

We found that having the right size screwdriver made a difference especially dealing with rusty screws. It was also handy to have a good flashlight. Having extra hands was helpful to hold the control panel and cover while working on the solenoid and routing the wires.

First remove trim surrounding ice/water dispenser assembly. Use a flat spackle knife to obtain space between door and trim. Be careful not t scratch refrigerator door. Then pry trim off. This was the most difficult part of repair. The front plate of the dispenser is held to the back of the dispenser by two friction fastners and in the case of my refrigerator a phillips screw (some don't have screw in middle). Use a small round tool like an allen wrench to push up on the 2 fastners to release them. Next push the front assembley aside and remove the 4 screws holding the back part of the dispenser. Push that assembly aside. Remove the defective solenoid assembly by removing the 3 mounting screws. The solenoid base can be worked out by slipping it out of the solenoid assembly plunger still attached to the dispenser door assembly. Next slide the plunger off of the dispenser door assembly. Install new solenoid assembly by reversing this procedure.
Hint - I found the ice door assembly (wr17x11653) also needed replacement and it is well worth the effort to replace both at the same time.

Unplugged refrigerator. Unscrewed back cover. Unscrewed dual water valve. Unplugged electrical connections 9red and yellow) . Shut off water valve from wall to refrigerator. Cut black tube (ice maker, cut translucent tube (water line). Connected new valve to water supply. Reconnected black and translucent tubes to new valve. Reconnected yellow and red electrical plugs. Turned on water supply plugged refrigerator back in.

Unplugged the unit and turned off the water line to the refrigerator. Removed the six screws holding the back cover. Removed the screw holding the outlet water valve. Unplugged both electrical connectors. Unscrewed the water supply line and cut the ice maker and fresh water outlet lines from the valve. inserted the fresh water and ice maker lines into the correct valve and connected the supply line to the inlet. Connected the electrical lines and remounted the Valve. Turned the water on and checked for leaks. Remounted the Valve and installed the back cover. Plugged the fridge in and ran the front fill until water came out (1:00 minute). Cleaned up and pushed unit back into cabinet.