38185KBPARBB General Electric Refrigerator - Instructions

My fridge came with only a single snack pan, and since the glass shelves are identical I decided to order the parts needed for installing the second snack pan. The glass shelf is secured in front by a round plastic pin protruding from the side of the fridge. Once the shelf is lifted upward and free of this pin, the rear retaining ears on the metal shelf side brackets can be released from the vertical-slotted metal track at the rear of the fridge. Make certain that you have the Right and Left snack pan slides oriented correctly, and positioned on the correct side of the metal shelf brackets. You’ll need to thread two self-tapping screws into each of the snack pan slides: one near the front, and the other at the rear. These screws extend through the metal side brackets into pre-aligned holes in each pan slide. When this is completed, you can test-fit the new clear plastic pan slide (drawer) into the slides to make sure it fits correctly. All that's left to do is insert the retaining ears into the appropriate pair of slots at the rear, then lower the front of the glass shelf until it's properly positioned over the plastic support pin. Now you're ready to enjoy twice the snack pan capacity as before!

I used the socket set to remove pannel that allowed me to have access to the evaporator fan. Once the fan and it's container was visible, I removed the entire fan container using the socket set. I took the fan out of the container, removed the damage blade and the damaged fan grommets. I then replace the old blade with the new blade and put the fan and the compartment back together. I am not very handy so if I am able to do this, anybody can. Ps. I was very very pleased with the services I received from PartSelect and would encourage others to use them - must admit I was very suspicious at first.

Had to e-mail GE for electrical schematic. Checked voltages to compressor. Jumpered compressor to see if it would even come on. Found bad run capacitor. Fixed.

replace the bar lift top off

removed the inside fridge electrical panel and swapped switches

easy pry out, disconnect wiring, connect on new switch and press in switch.

layed fridge face first on a chair removed cover with flat head screwdriver unplugged part replaced with new part replaced cover returned to upright and plugged in

Pulled the old gasket off, approximately 5 seconds. Put the new one in, starting from the corners, with no tools, approximately 2 minutes. Coated gasket with a thin film of petroleum jelly, approx. 1 minute.

I started removing the switch by prying on the right side with a screwdriver, when it emerged enough I used pliers to finish removing it. I then unpluged rhe wires from the bad switch and pluged them on the new switch and "poped" it into the hole.

Connected the 2 wires and pushed in the switch until it clicked.

Only took a screwdriver to take two screws out & install new slide with the two existing screws. Very easy. Took less than 5 minutes. Great website I found on Google right away, just by searching for refridgerator parts. After ordering part, only took a few days to come in.

2 screws. how easy can i get.

Gently pry out switch in door jam with screwdriver and pull both connectors off and put connectors on new switch then push switch back into the hole. Looked it up on the internet and video showed how to and also had link to new part, ordered and less than a week later the fridge is bright again. I have an older freezer also and it seems that they all use the same switches. Very Very easy

Simply unplug fridge, remove air duct mounted on rear panel, release panel itself, pull fan blade off, disconnect grounding wire, detach fan motor bracket, disconnect wire harness to release fan motor, install new fan motor and reconnect, secure with bracket, reconnect grounding wire, reposition fan blade onto motor shaft, reinstall rear panel and secure screws. Remount air duct and plug appliance back in. This is the second motor that was replaced since 2002. The 1st motor dies after 5-6 years.

I followed advice from other posts on this web site. The only thing additional I'd recommend is to take pictures of assemblies before you disassemble them. A neighbor gave me that useful tip. It should be noted that I first noticed my refrigerator failure back on June 22, 2012. I hired a reputable local repair service to fix it. They replaced the Defrost heater (item 618) and charged me $ 208.14. Then on August 22nd, I noticed that the problem resurfaced. I decided to fix it myself using info from site. The repair went well, and I'm hopeful that it will stay repaired. Kudos to this site!