ZISS480DHBSS General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Dan from COLUMBIA, SC
- Parts Used:
- WR55X10025
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set
Refrigerator not getting cold
Replaced Temperature Sensor and now it is getting cold.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cary from ORLANDO, FL
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Ice maker stopped working
Remove the one screw holding the unit in place, unplug it, slide in the replacement, plug and screw it in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from BOZEMAN, MT
- Parts Used:
- WR02X12008, WR02X10540
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Noisy Freezer Evaporator
Find a video on youtube. Remove 6 screws. Pull the Styrofoam part up before removing the panel. Unplug and Remove the fan assembly.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.
You will need a NUT DRIVER to take the bracket off the backing plate.
I ordered the red grommet and the red bumper. You need TWO of the red grommets if that is the problem. My freezer was about 8 years old, and the grommets were worn and compressed, the bumper was not. Replacing these parts DID NOT FIX the problem. I needed a new motor.
I probably disassembled and reassembled this stuff about 7 times before I got all the parts and tools. Each time I had to unload the freezer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from FORT MYERS, FL
- Parts Used:
- WR62X10055
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The flapper on the ice dispenser would not close after you dispensed ice cubes
Removed face plate, which holds the circuit board. Removed the next section be removing the 4 screws that hold it in place. Then removed the old solenoid, and replaced it with the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Tim from SANTA FE, NM
- Parts Used:
- WR17X11653, WR17X10706, WR02X10585
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Frost in upper portion of freezer
Removed escutcheon, removed control panel, remover and replaced flapper, spring and crank. Followed the instruction exactly. Although I hope this fixes the frosting problem, I did not see anything wrong with the parts I removed. I hope this fixes the problem,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES from MORENO VALLEY, CA
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Water dispensed at a trickle
I only had to remove the old filter and install the new one - all by hand. I then ran about 1 to 1and1/2 gallons of water through the filter to clear it.
A WORD OF CAUTION - HOLD YOUR GLASS CLOSE TO THE WATER DISPENSER FOR THE INITIAL FILLING - IT WILL SPIT UNTIL THE AIR IS PURGED FROM THE SYSTEM!!!
An extremely easy repair.
A WORD OF CAUTION - HOLD YOUR GLASS CLOSE TO THE WATER DISPENSER FOR THE INITIAL FILLING - IT WILL SPIT UNTIL THE AIR IS PURGED FROM THE SYSTEM!!!
An extremely easy repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Justin M from Cypress, TX
- Parts Used:
- MWFP, WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice door gasket warped would not seal
Pop off the control board for the ice selector/water. Remove power / signal connections. remove four phillips screws, Remove plastic hopper. Pop off Ice door gasket, pop in new one and put back together. If you fridge was sounding like it was speeding up and slowing down, this will correct this problem as well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Sandy Hook, CT
- Parts Used:
- WR62X10055
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice chute wouldn't open or shut correctly - rusted solenoid
Replaced rusted solenoid.
Popped front button panel off from the bottom using flat head screwdriver; Removed 4 screws holding electronics board and disconnected wires. Unscrewed 3 phillips head screws on old solenoid and replaced with new part. Reconnected wires to board, screwed back in, and pushed panel back into to place.
Thumbs up to PartSelect - fast, straightforward service and fast delivery.
Popped front button panel off from the bottom using flat head screwdriver; Removed 4 screws holding electronics board and disconnected wires. Unscrewed 3 phillips head screws on old solenoid and replaced with new part. Reconnected wires to board, screwed back in, and pushed panel back into to place.
Thumbs up to PartSelect - fast, straightforward service and fast delivery.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- NICK from COCOA bEACH, FL
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice dispenser door will not shut completely
I removed the door cover plate and disconnected the circuit board, then four screws. The part was corroded in place. Upon removing three screws and cleaning the surface, the new part was an exact fit, replaced it and everything works like new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeff from stillwater, OK
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
solenoid quit working
repair was easy, just removed control panel and removed screws from solenoid, switched out with new, was done in minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from W Berlin, NJ
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice forming around shoot. Flapper door not shutting letting warm air in.
I followed they instructions from the other "do it your selfers" but only replaced the solenoid. This was the cause. Rust was keeping solenoid plunger from moving and this held the flapper door open. Very easy to repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joanne from Fort Smith, AR
- Parts Used:
- MWFP
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Auto water stopped working, found that filter needed replacement
Unscrewed old cartridge, ordered new cartridge, installed new cartridge by following very simple instructions. Took only one day for part to arrive from PartSelect although I paid for cheapest shipping, which was "ground." I was amazed!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from BRICK, NJ
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My ice container and Ice chute were freezing up and getting blocked, and my filtered water line was also freezing
I just followed the instructions on the video and it was exactly as they said......no surprises.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from CAMARILLO, CA
- Parts Used:
- WR17X22070
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Leaking around filter bypass plug
Took old one out with my fingers. Put new one in with my fingers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from TYLER, TX
- Parts Used:
- WR62X10055
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Your video was wrong. Your step was to remove exterior frame on ice/water outlet. No need to remove.Wasted too much time trying to remove.
Remove control panel.
Remove four screw in control panel bracket.
Remove to bottom screws at bottom of solinid loose top screw.
Replace all screws.
Remove four screw in control panel bracket.
Remove to bottom screws at bottom of solinid loose top screw.
Replace all screws.
Was this instruction helpful to you?
Thank you for voting!