STS18HBMFRWW General Electric Refrigerator - Instructions

I opened the back panel of the fridge and exposed the compressor. Unplugged existing run capacitor and installed new one with the addition of the sleeve that is stated must be installed around the run capacitor.
Everything I read and on this web site says that based on these symptoms, that the problem is the run capacitor. I searched and search for a part called a start relay which plugs in to the compressor. This run capacitor plugs in to this other part which I take as the start relay.

Installing this run capacitor did not solve the problem. The fridge compressor keeps cycling on and off. Freezer doesn't keep as cold as it should.

This is a built-in unit. Remove the external bezel at the top of the unit. Reach through the unit and unplug the frig. On the compressor unit, you'll see a vertical metal panel. Remove the metal panel and the timer is right behind it. Remove one wire at a time and switch it to the new timer. Remove timer and replace with new one.

Just an added comment, GE Service wanted to put an "ice kit" into my unit. The full repairs would have cost $1,000. While I described how to replace the defrost timer, the problem was the tray heater. But that's another story.

Removed freezer cover, removed fan and fan motor, and bracket holding the fan moter. Installed fan, installed motor and wa-laugh, done.

I noticed that if I unplugged the refrigerator and plugged it back in a while later it would start working but eventually would stop. I deduced the problem was likely the defrost thermostat. I ordered the thermostat but it was in a difficult place behind the evaporator coil which I could not remove. While I was trying to work it into position my hand pressed against the defrost coil and shattered the glass sheath. I ordered the coil and finally managed to get it and the thermostat installed. The refrigerator seems to work fine now.

took out 4 screws - lowered timer cover - replaced timer- put it back together

I did folllow the instructions on the video step by step.

I removed the shield over the timer and the part that supported the timer. Just unpluged it and pluged in new timer and put back shield. I had already replaced the defrost heaters which had totally burned up. I also replaced the thermostat while I was making the repairs although the old one was still o.k. All the information that I needed to make the repairs I obtained through your website. After looking at several websites to compare prices-etc, I found yours to be the best overall. Thanks-a-million your website is worth it's weight in Cold Food !

From instructions found on the site I was directed to the defrost timer part being bad. And from the information others posted that have had the same problem I was able to replace that part by removing the bottom grill just below the door and on the left side was the part. Removing one screw to remove the bracket from the frame and then another screw to remove the part from the bracket. I found it easier to remove the part from the bracket before I pulled the part out so I would have more room to unplug the connector. Just reverse the steps to replace the new part. It took about a day or so for the refrigerator to get to the proper temp.

Removed freezer bottom and back plates-encountered ice -melted with heat gun.Observed fan not running with fridge plugged in and considerable erosion of the styrofoam part.ordered fan motor and blade and styrofoam ducting and replaced same.Fan started running immediately when plugged in and now the compressor cycles normally and the refrigerator compartment is much cooler and icing has stopped. I'm good to go until the compressor fails! thanks for the excellent delivery service(2 days)and your parts diagrams really helped me trouble shoot the problem.

common sense,removed plate,removed mounting bracked,unplugged,reversed order,and that was it.

I took the advice off of your website about the only thing that will fix
the problem is change the run capacitor. I felt assured that I would
have a working refrigerator freezer after making this change. I was
pretty disheartened when it didn`t solve anything. I was not going to
take the new part back out after the small challenge of putting it in.
The next day I found out how to test the old capacitor and it was still
good. I will just have to eat the $49. I did learn not to take advice from
a website even if it seems like a sure thing

Easy fix - snapped together.

4 screws in the freezer and the back panel came off then 2 more screws to take the motor off. I unpluged the old motor pluged in the new motor put the back panel back on and I was done.

first I ordered parts that didn't work. the return process was painless and I found the part I needed, which just popped right in!

I FOLLOWED YOUR VIDEO............WAS EASY. THANKS