GTS18DCMCRCC General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- James from NEW YORK, NY
- Parts Used:
- WR02X10540
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
noisy refrigerator
I followed your video and completely dismantled the refrigerator evaporator motor, fan, brackets, and grommet, I completely cleaned the refrigerator including the cooling coils. I then ordered the evaporator motor ,fan, grommets, lid bumper, and brackets. The order would take a week to arrive. In the meantime I cleaned and reassembled all the old parts, waiting for the new ones to come. Guess what! The refrigerator was quiet as a mouse. I really did not need the new parts, but I kept them anyway just for good luck. Not bad for a refrigerator that's twenty four years old.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANK M from EASTON, PA
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers, Wrench set
Ice Maker was not working
1st - checked water supply - old valve in water line was closed with sediment.
2nd - replaced water line valve and reconnected copper tubing about 1 hour
3rd. removed single outlet valve and installed the new part - about 15 minutes
Everything went well and was very easy.
Unfortunately, the ice maker still does not work.
Still trying to understand what is wrong.
2nd - replaced water line valve and reconnected copper tubing about 1 hour
3rd. removed single outlet valve and installed the new part - about 15 minutes
Everything went well and was very easy.
Unfortunately, the ice maker still does not work.
Still trying to understand what is wrong.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Louis from LEAGUE CITY, TX
- Parts Used:
- 40A15
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Change bulb
Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Willie from Virginia Beach, VA
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench set
Ice maker traydid not fill with water
Unplug electrical power to refrigerator. Disconnected electrical power to water valve, Disconnected water inlet and out let lines from valve. Remove screw holding valve on refrigerator, removed and replaced water valve with screw. Connected inlet and outlet water lines, turned on water and checked for leaks. Connected electrical power to water valve, plug in electrical power to the refrogerator. Ice maker tray fill, made ice.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ted from SANDWICH, IL
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken light switch
took a little more effort than the video show to remove old module and replace new. Works fine now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from Sanford, NC
- Parts Used:
- WR57X10033
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
valve wouldn't allow enough water to fill ice maker.
Started with a visual inspection.
Turned off water.
Removed old valve.
Bent bracket to facilitate installation.
Installed.
Hooked up.
Tested.
Works as advertised.....
Turned off water.
Removed old valve.
Bent bracket to facilitate installation.
Installed.
Hooked up.
Tested.
Works as advertised.....
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from KEARNY, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Light was flicking
It was way to ez to install only a couple of minutes that's it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Port Republic, MD
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
Small Ice cubes/Jams
My Son removed two screws, electric plug and two (2) compresion nuts. He had to bend the bracket to fit, then replace it, in reverse order except the filler tube on the new valve was of a "stabb-in" type. Job was a piece of cake and this small project, solved all our problems with the Ice maker.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Fred from Crawfordsville, IN
- Parts Used:
- WR57X10033
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Wrench set
No water to icemaker
Shut the water off, removed two screws,removed the inlet, from the water valve then the line from the valve to the ice maker. Then you reverce these steps and you are done. The shipping time was the best I have ever seen. Thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Eugene, OR
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door activated light switch was missing.
Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Lake Helen, FL
- Parts Used:
- WR57X10033
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Mounting bracket did not fit. Retainer for water input looked like a thread protector.
Put bracket on workbench and hit two or three times with hammer. Glad I did not remove water inlet retainer from part, it can very easily be mistaken for a thread protector.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Boyd from Rapid City, SD
- Parts Used:
- WR02X10098
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The evaporator fan in the freezer compartment began making a loud noise.
I found a replacement evaporator fan motor and 2 mounting bracket grommets at PartSelect.com at a reasonable price. I watched the installation video provided and installed the new parts as shown in the video start to finish installation time 22 minutes.i
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Sylva, NC
- Parts Used:
- WR23X37285
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Bad switch for door prevented interior light from coming on
Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harvey from Harrisonburg, VA
- Parts Used:
- WR32X10457
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
The cover on the Veg. pan was broken so the Veg. drawers would not work or stay in place since the tracks were broken on the sides and the center guide was broken also, had to replace both parts
Simple just remove the old veg. cover and the center track and replace both parts. Removed the rubber seals from the old veg. cover and installed on the new cover.
One problem I found out the drawers were not interchangable, the drawers have to go in a certain way and should not be sewitched from one side to another. I found that moving the drawers to the right position corrected the problem. The left drawer was bumping and did not work corectly until I swithche the drawers around. Also the GE Service man was here for a repair when we first moved in and the fridge was new and he gave me a tip about the drawers. He said to put a little cooking oil on your finger tip and rub it on the drawer slides, it makes them slide smoothly and freely.
One problem I found out the drawers were not interchangable, the drawers have to go in a certain way and should not be sewitched from one side to another. I found that moving the drawers to the right position corrected the problem. The left drawer was bumping and did not work corectly until I swithche the drawers around. Also the GE Service man was here for a repair when we first moved in and the fridge was new and he gave me a tip about the drawers. He said to put a little cooking oil on your finger tip and rub it on the drawer slides, it makes them slide smoothly and freely.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TODD from PLAINVILLE, CT
- Parts Used:
- WR02X12149, WR60X10172
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Fan stopped working, Ice maker burned out
Fan Quit So did the Ice Maker. $150.00 worth of parts plus my time. Also the Freezer Floor cracked for some stupid reason.
Was this instruction helpful to you?
Thank you for voting!