HTH17CBDDRCC General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- merlin from TRENTON, NJ
- Parts Used:
- WR32X10398
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
cover was cracking on sides
removed bins ......removed cover .....replaced with new cover....replced bins back .....done !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Maureen from LYNCHBURG, VA
- Parts Used:
- WR60X31522
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Refigerator was amking a loud noise when the fan came on to cool.
Followed the on line instructions and found the repair to be very easy. Took longer to remove the food from the freezer than to switch out the fan motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Claudette from JUPITER, FL
- Parts Used:
- WR12X10973, WR12X10972
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
No instructions came with the item. Needed screwdriver and Hex-L Key
Used my Philips Screwdriver for 5 of the 6 screws. But Hex-L key I bought was metric and did not work. Had to get somebody with necessary tool to finish the job. So instructions should have been in the box. Otherwise I was very satisfied.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicole from ST GEORGE, UT
- Parts Used:
- WR17X11889
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
crisper drawer shelf holder broken
Easy peasy
take the drawer out and the glass from the shelf above the drawer and the frame thet holds the glass.
Then place screwdriver at pin and knock it through. Use putty knife to pull old piece out. Then place new piece in and hammer the pin in place. Put frame back in, glass back in and drawer back in.
take the drawer out and the glass from the shelf above the drawer and the frame thet holds the glass.
Then place screwdriver at pin and knock it through. Use putty knife to pull old piece out. Then place new piece in and hammer the pin in place. Put frame back in, glass back in and drawer back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ella from RODESSA, LA
- Parts Used:
- WR17X11890
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
None
Just place the shelf door bar in slot and push in place gentle.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronnie from BATON ROUGE, LA
- Parts Used:
- WR82X10111
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
had no access cover on back
screwed the cover on just like the original
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Janice from LORENA, TX
- Parts Used:
- WR32X10398
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Crisper drawer cover was missing
I simply slipped in the new drawer cover and put the drawers in. So easy!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Catherine from SEATTLE, WA
- Parts Used:
- 40A15
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light inside the oven had burned out
0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.
No tools needed, the cap is just held in place with pressure from the wire.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- J.Larry from TALLAHASSEE, FL
- Parts Used:
- WR17X11889
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
replaced a plastic shelf on the door
shelf just snapped into place. It was so simple, "even a caveman could do it."
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jo from MCDONOUGH, GA
- Parts Used:
- WR17X11889
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Parents in assisted living. Frig was missing a shelf.
Just put the refrigerator door shelf in. Was to happy to fix this missing piece. So glad this company was able to supply an old part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ellastine from SAINT LOUIS, MO
- Parts Used:
- WR17X11890, WR32X10398
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
No instructions needed or problems.
Both items were very easy to install. Just took the cracked parts out and inserted the new parts. No video needed. Just what I needed. Thanks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deborah from BRADLEYVILLE, MO
- Parts Used:
- WR23X37285
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Broken light switch
This was so easy I think it took me 2 minutes. I am not very mechanically inclined but that didn't matter! Works perfect thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Matthew from Escondido, CA
- Parts Used:
- WR02X12008
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Fan making noise.
Remove ice maker and all of it's accessories in order to remove the panel covering the fan. Don't drop the screws!
Unscrew the lower fan bracket. You will see the lower red rubber grommet. Hold fan motor with one hand and push the fan off the shaft and into the compartment above. Then remove the round retainer thing below it by holding it and pulling down on the motor assembly. Install new grommet on upper part. and put it all together.
REMEMBER where the fan is on the shaft. It has about one inch of shaft placement. I put mine so that most of it was above the hole that the fan goes into and about 20 percent showing below the sheet metal.
Also check to see if your fan is damaged. Mine was not.
This refrigerator has been awesome! I have had many issues but have been able to fix all of them for the last 15 years!
Unscrew the lower fan bracket. You will see the lower red rubber grommet. Hold fan motor with one hand and push the fan off the shaft and into the compartment above. Then remove the round retainer thing below it by holding it and pulling down on the motor assembly. Install new grommet on upper part. and put it all together.
REMEMBER where the fan is on the shaft. It has about one inch of shaft placement. I put mine so that most of it was above the hole that the fan goes into and about 20 percent showing below the sheet metal.
Also check to see if your fan is damaged. Mine was not.
This refrigerator has been awesome! I have had many issues but have been able to fix all of them for the last 15 years!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James from GREENSBORO, NC
- Parts Used:
- WR02X12008
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Fan was not centered in the middle of the back panel opening.
Bent the motor bracket down, then using a rat tail file, elongated the holes in the back panel of the refrigerator to secure the fan in the "centered" position. This was a problem that was with the refrig. since it was made. The parts involved were perfect. NO problem at all installing them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from E LONGMEADOW, MA
- Parts Used:
- WD2X5166
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable)
water leaking from under dishwasher
Water was leaking from under the GE dishwasher, but once we pulled it out, had apparently been going on for a little while. Turning the water off to the dishwasher made it stop, so it was happening even when the unit was not running, potentially indicating somewhere early in the path of the water to and into the machine.
Indeed, inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.
A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.
Indeed, inspecting the water inlet vale showed a slow leak. Getting the replacement part was fine, and it fit the electrical, water inlet (existing 90-degree water inlet elbow), and water outlet connections just fine - but the original machine screws that held on the original water inlet valve did not work. It took a little research to figure out the new type of screw required, which was apparently a 10/16 Type AB, which seemed to be a less common type of sheet metal screw (with a point), as opposed to the original flat-ended machine screws. So, after ordering those separately (which were a bit expensive), it went together fine.
A note on the water inlet valve part just indicating the the threading on those parts has changed over time, so potentially ordering the screws to attach it might be worthwhile, would be good information to add about the water inlet valve.
Was this instruction helpful to you?
Thank you for voting!