GTS16BBSERCC General Electric Refrigerator - Instructions

First, I love that fact that my new fridge piece came in the mail in 2 days! I didn't order it as a rush, but I'm so glad it came so quickly! The installation could not have been easier! It took me longer to clear off my broken vegetable pan cover than it did to pop the new one in. My overall experience was amazing and super easy! I'll be back to PartSelect should I need I need to replace anything else in the future.

new cover slipped right in place, however, the way the new one is designed, the hump in the front rubs the bottom of the door. you have to make sure you push the door shut or it will remain open .

Extremely easy repair, the hardest part was getting the old switch out. I used a pair of needle nose pliers to squeeze the tabs in and it came right out.

put the gratefruit knife behind the old switch pooped it out pluged the new one in piece of cake 5min.even vacumed the dust off the coil

Remove the top cover above the door by lifting it slightly and pulling forward. I used a mirror to make sure that there was nothing in the way of accessing the switch from above. I used a blade screwdriver to press against the switch retainer on the topside, while GENTLY prying from below with another blade screwdriver to get the switch dislodged. Once the retainer was past the opening, I wiggled the switch downward and then rotated it to the left when the rounded top right edge of the switch was visible. This allowed the wiring to the connector to pass thru the hole. I pushed the wiring from the top and pulled from below to get the connector below the opening for the switch. I then unplugged the switch, plugged in the new switch and reversed the removal process feeding the connector thru first then rotating the switch to the right to get the rounded edge of the switch thru the opening, then pressed the switch up into the opening until it snapped into place. Total time less than 10 minutes.

Simple. Rolled the refrigerator out , unplugged the 120 volts AC outlet.(1) Unplugged the wiring from the cabinet to the fan (white (three pin connector)). (2) Removed the two 5/16 inch screws holding the rear motor bracket . (3) Removed the fan blade from the motor shaft by applying slight pressure, pulling if off the old motor shaft. (4) removed the rubber isolator from the frame and from the rear of the old motor. (5) placed the rubber isolators back on the motor and frame. (6) Pushed the new motor back into the frame and re-installed the fan assembly. (7) remounted the fan with the rear support and the two 5/16 inch screws. Reconnected the three wire connector. Just checked the fan blade assembly to make sure they were not hitting the fan shroud. Fan blades should sit just partially inside the shroud to make sure it produces maximum airflow.
(8) Reconnected the 120 volt AC and waited for the compressor to cycle back on... Nice quite fan... Thanks

Just put the refrigerator door shelf in. Was to happy to fix this missing piece. So glad this company was able to supply an old part.

Slipped it it-very easy

0. As a safety precaution, unplug the range or hit the relevant fuse breaker before you start. You might also want to grab a flashlight. Definitely do not try to do this while the oven is hot.
1. Pinch the wire over the light bulb cap to remove it. This is inside the oven at the back.
2. Pop off the hemispherical glass cap.
3. Unscrew the old light bulb, and screw the new light bulb in its place.
4. Put the cap back.
5. Secure the cap by putting the wire back in its slots on the cap.

No tools needed, the cap is just held in place with pressure from the wire.

Easy peasy
take the drawer out and the glass from the shelf above the drawer and the frame thet holds the glass.

Then place screwdriver at pin and knock it through. Use putty knife to pull old piece out. Then place new piece in and hammer the pin in place. Put frame back in, glass back in and drawer back in.

Just place the shelf door bar in slot and push in place gentle.

screwed the cover on just like the original

with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back in SNAPP

Pop out switch, pull wires, attach wires to new switch and pop back in. Easy smeasy!

First I unplugged the power. Then I removed the wire shelf, center plastic cover, flited the stryofoam piece out, removed the back panel. Then I disconnedted the fan connectors. Then I took the fan brackets off and removed the clamp holding the fan blades to the motor shaft. I then reversed the steps to complete the installation.