PFSF0MFCABB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- paul from east hanover, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
refig light did not work
per your instructions
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Island Lake, IL
- Parts Used:
- WR55X10025
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
frige too cold
changed sensors did not repair problem,replaced damper with mechanical damper fixed problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ajaykumar from Plainsboro, NJ
- Parts Used:
- WR60X10209
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The refrigerator was making load and unusual noises.
I identified the noise was coming from the coils / and the fan. Cleaning the fan helped reduce the noise a bit but it still kept recurring. I ordered the part, which was really easy using the diagram on the website. The instructions and the video were really helpful and was able to remove the old motor and replace it with the new one with relative ease. While there I cleaned the fan blade and vacuumed the surrounding area. This whole repair went quite smoothly and has given me the confidence to take on other repairs before calling out the repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- joseph from myrtle beach, SC
- Parts Used:
- WR57X10086
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
ice maker not making ice
I looked up appliance on internet,diagram only showed the inlet valve and ice maker in schematic.I ck'd to see if water was getting to valve(it was)but wasn't getting to ice maker,thus I replaced the valve and it solved the problem.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marco from Fallbrook, CA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
My fridge was colder than my freezer
I can't tell you how luck I feel after finding your website I ordered the temperature sensor after watching one of your videos on-line and the repair went just as on the video. I pulled the "bad" sensor out, and replaced it with the new one. Keep in mind that this is the first time I ever touch an appliance, needless to say I'm feeling pretty good about that! All in all it took me about 20 minutes to complete my repair and it now has been about 4 days and the refrigerator is working like new again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kevin from Ramona, CA
- Parts Used:
- WR60X10209
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Refrigerator not cold enough
The repair is a snap, you can watch the video and it will put you on the right path. My story is more about the service that Part Select gave me. I used a small box fan on low as a temporary fix. My model number was worn off from the box wine we store in that particular place. So I ordered the part based on looks, well it was wrong. Called Part Select and we talked, the nice lady on the other end said OH it must be this fan motor. Send us back that one, and I'll get this out too you. I'll credit your account for $7.99, and it cost me $8.99 to ship back the wrong part. Wow, the next day I received the new motor. They sent it overnight! I thought it would be 5-6 days! Unbelievable. I will use this company for any, and all my repairs.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- chol from Glenview, IL
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
refriger warm
replace sensor in refriger.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from Rockwood, TN
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Would not self defrost.
Remove the shelves then remove the back by removing the two screws at the top of the panel. Locate the temperature sensor on top of the coil. Cut the wires and replace with the new one. Use wire nuts and electrical tape to reconnect the wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jerry from Chipley, FL
- Parts Used:
- WR57X10086
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
It was broken
Then I fixed it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- PHILIP from JACKSONVILLE, FL
- Parts Used:
- WR57X10086
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
ice maker would turn on to allow water into ice tray and would shut off. water would over flow, eventually out of the freezer
replaced the icemaker inlet valve. works like a champ now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Simpsonville, SC
- Parts Used:
- WR23X37285
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
light switch quit working
removed the inside fridge electrical panel and swapped switches
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ANTHONY from NEW EGYPT, NJ
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
sticky switch
easy pry out, disconnect wiring, connect on new switch and press in switch.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marlene from Monument, CO
- Parts Used:
- GSWF
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Just Needed A New Filter
Pressed the button, took out the old, put in the new. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Zachary from Decatur, GA
- Parts Used:
- WR55X10025
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Fridge was freezing food near the back, adjusting internal temp not fixing the problem
Unplugged the refrigerator first....then on the inside of the fridge, I popped the temp sensor cover off (upper LH side) and exposed the old sensor. I snipped off the old sensor about 3" down from the end and connected the new sensor (which I trimmed down to about 3" long) with some heat shrink wire nuts/connectors. Let the fridge run for a day or so and confirmed the problem was solved! Oh yeah, there was no way to tell the 2 wires apart (power vs. ground) on the sensor. However there was a manufacturer's stamp on the wires. So note the orientation of the text and mark one of the wires with a sharpie on both the old and new sensor before trimming. This will give you a reference for which wires to connect when adding the new sensor to the old wires.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- TREVOR from KENT, WA
- Parts Used:
- WR72X10072
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench set
broken slide drawer track
Took out shelf, unscrewed old track, screwed on new track. Only thing is not a standard flat or Phillips screw head so if you don't have a star head bit, you are out of luck.
Was this instruction helpful to you?
Thank you for voting!