PFE29PSDESS General Electric Refrigerator - Instructions

Repair man thought it was the control board and an issue with a relay on the board. Purchased the new board but found out the board was fine, and it was the recirculating fan that would go out intermediately.

Tried ordering that part from Part Select since they have been great, but GE discontinued the part and their was not a replacement available. After much research, found the new replacement part number and ordered that, it went in quickly and for now seems to have solved the problem.

It was super easy! The glass came packaged and safe. Once I unwrapped it, I slid it in the firdge and it just popped into place. So super easy. And now we know for next time when taking it out to clean, (the reason it shattered in the first place) you should let the glass get to room tempurature before cleaning it with water or it will shatter! OOPS!

Removed the bad inlet valve and installed the replacement. Very easily done. The replacement part made the repair so simple and saved me a huge amount over calling a repair man. It did not take any special knowledge.

Move the refrigerator away from the wall.
Disconnect the refrigerator.
Remove bottom drawer.
Remove two criisper drawers.
Remove crisper drawer slides, one bolt near the front of each slide.
Push slides off pin at back.
Remove bottom panel at the back of the refrigerator to access fan.
Remove fan, held with a couple of screws.
Remove rubber gasket from around old fan and put the gasket around new fan.
install new fan and bolt in place.
Replace lower panel at back at back of refrigerator.
Reinstall drawer slides, hook at back and bold at front
Reinstall drawers.
Reconnect refrigerator power.
Push refrigerator back in place and adjust feed to hold in place.

Search online and came across PARTSELECT website!!! this is amazing when I opened the website and see a labeled drawing, so I know what part number to order, it arrived on time and when I install it fits very well, one lesson I've learned is whenever you removed this glass in the chiller box you have to reinstall the glass properly by inserting one of the side to the insert slide of the chiller so it will not move! I'M VERY HAPPY!!!! THANKS!!!

Received replacement part. There is a cover over the ice box latch. Pried it off with a screwdriver head. Took the broken latch off replaced new latch to cover and replaced on the door.

I used pliers to pull lightly on the head of the switch, while I inserted a small flat head screw driver into the base of switch and gently worked around the edges to free it from the panel.

EXCHANGED THE LED LAMP ASSEMBLY. ONLY DO ONE AT A TIME AS THEY ARE WIRED IN SERIES!

I went on line, found PartSelect, located the diagram for our model, selected the part and ordered it. The part arrived in about 5 days, well packaged. We removed it from the packaging, and installed the new shelf. Extremely easy process. The exploded diagram on the web site allowed me to make sure I was ordering the right part.

Excellent process!

It dawned upon us, after stumbling across chunky milk and crisper starting to freeze items, perhaps the fridge was not working properly. Checking temps the compartment would run 57 to 59 deg F, yet the freezer was perfectly fine 0 deg F. Rather than trouble shoot what component was the driving issue, I decided to replace all the main components: motherboard, compartment fan, blend door assy. Motherboard was quite simple: two screws for a cover on the back, unplug all the harness connectors, plug back in. Compartment fan simply slid out and new one back in with a little trickery for the wiring (I just cut the old fan harness rather than fight the wire routing plastic piece). The blend door assy was the most complicated but just a series of 1/4" nut screws and disassembly. Fridge now maintains 35 deg compartment temp. I'm not certain which component was the culprit (leaning towards motherboard, as I look back some the interior lighting may not have been working properly, which also suggest MB), however I'm glad $450 in parts brought fridge back to life any not $3k for a new one.

The old switch was hard to remove. Thinking that I may have to loosen the wires I used a socket wrench to remove a clamp. This was unnecessary. In the end the switch did come out using a large size screwdriver. The problem was that the expanding plastic tongue is not visible from the ouside so you have to try to feel your way around. If i had ordered the replacement before and not afterwards I would have seen this before hand.

After replacing the light bulb and still no light I manually pushed the light switch button. Intermittently the light would come on then go out. I removed the power plug from the power source then replaced the light switch. I plugged the refrigerator back in and now I open the door the light comes on and stays on until the door is closed.

I ordered two switches, replaced both with a knife in 10 minutes. Interior light works, thanks.

Removed back wall cover over coil. Defrost all ice with a hair dryer. Cut white wires and replaced Temperature Sensor. It has been working for a week and no trouble at this time. If you have this system on your GE refrigerator do this before replacing the motherboard. I must admit I was thinking that was the trouble. Motherboard was replaced after 5 years old now 5 years later my thinking is this a 5 year problem. So try the Temperature Sensor.

I ordered the correct part, the box said it was the correct part and when I opened the box a completely different part was inside. Not only was it the wrong part but it was loosely wrapped with very thin plastic and the hinge was broken off of the lid and laying in the box. I have called and emailed for help and was told no one was available to help because of COVID 19. One email was answered to return the part I would have to pay shipping and the part could not be damaged. Okay, the part was wrong, the part was broken. Now what should I do? Please respond.