PSE29KSECCSS General Electric Refrigerator - Instructions

Part arrived very fast as ordered..need to pry old switch out from top..use care to push the retainer down..after old switch was 1/2 out, I used a putty knife for better leveridge.Remove wire connector...after plugging in the wire connector to the replacement switch, make sure the switch is properly positioned so the switch will depress when door shuts.

shut off water supply to unit, pull the unit out,unplug, unscrew lower back cover, locate valve relay unit (bottom left, black and clear hose coming out of it) undo the quick connect for the clear water hose on the right (black one is for ice).

front of the unit, bottom left, locate the other hose (longer one) running to the freezer door from under the unit, undo quick connect.

Inside unit, remove middle drawers, careful with the glass panels as these just lay on top and are not fixed.

undo the 3 screws for the old tank, pull it out, snake the hoses thru the grommet on the bottom, reverse process...all set!

The motor shaft stripped and the drive auger spun in place instead of driving the auger to rotate. I had to purchase an entire motor even though the motor itself worked fine. The shaft being stripped had to be hacked off to get the motor out of the assembly. New motor installed, new drive auger installed. Works fine.

Just pop the old one out, careful not to lose the wiring inside the ref wall & popped the new one in.

Dispencer quit working a year ago, but still still dispenced water. I talked to a service technician about it. He told me the electric motor was froze up, so I orderd a new one. When it arrived I installed it in about 20 minnutes,tried the dispencer and still would not work but this time the water would not dispence eather and this time I noticed the fan quit running and the light went dim when I tried to dispence ice. So I read the customers diagnosis and repares every thing pointed to the main control board, orderd the part and water filter. When they arrived in three days I watched installing this part video and it took me 20 minnutes to install and every thing works fine.

Remove ice holding box. Remove rear plastic cover (nut driver) Unplug two Electrical connectors. Place unit on work bench. Remove 'U' fork, vice grip on shaft and scewdiver as lever on fork (counter clockwise) Remove motor fron plastic Holder. Install new motor & fork. Reverse removal steps. Actually very simple procedure. Usual cost for this typwe of repair is approx. $300.00.

Replaced flapper

opened refrigerator door located water filter location in right back corner unscrewd 1/2 turn and out it comes without shutting off water it is a snap to do by anyone and shipment was really quick thanks. People do not call a service tech for something this simple even a child tall enough can do it.

look very carefully at the picture you provided in the parts fish, removed the ice maker tray and the rest was very easy ,i saved alot of money and time doing it myself.

My GE refrigerator emitted high pitch noise a short while ago. I tried different dampening methods that helped but not eliminating the problem. I finally replaced the fan, motor, and associated parts and solved the problem. The total cost was about $50.

Remove lower front panel, disconnect damaged union from water hose under freezer door, replace with new union, tighten and reattach front panel. No more water coming from under the unit. Ice maker and dispenser features returned to working order!

Turned off power, removed cover from Ice maker, checked resistance across thermostat for zero (read open), all other switches read proper value (when activated). Ordered and received thermostat. Removed Ice Maker from freezer, removed two screws holding ice tray to Control Assembly. Removed Thermostat and replaced with new one. Applied Silicone Sealant to face of Thermostat for adhesion to ice tray when assembled. Remounted Ice Tray to Control Assembly and remounted in freezer. Works Great...

i used the video it showed on the site or iwould not have been able to do it

Thanks to others who also gave some detailed instruction on repairs I was able to do the same. I have a GE Profile side by side refrigerator/freezer Model No. PSC25PSSCSS The first repair I did was to remove/replace freezer defrost thermostat sensor that is cliped to condenser tube I snipped the wires close to the thermostat and pulled it off the tube I stripped the ends of the wires and twisted the strands then placed a piece of heat shrink tube onto the wire pushing it away from the exposed wire then I soldered the two color coded wires together then I pulled the heat shrink over the conection and used a lighter to heat up the heat shrink until it sealed the conection repeating this on the othr wire as well. I then removed the Old defrost Heater element by removing to screws then I disconected the two wires by simply pulling the connector plugs off both ends of the heater element assembly. This fixed the freezer being too warm for a short time but it started getting warm again that's when I noticed the defrost fan was not working, when you have the door open to freezer push the door switch in you should hear the fan come to life and blow hard. The fan was replaced I had to remove everything to get to it it's pretty simple to do it just unplugs make sure you order the right fan though My fan comes with the Thermistor already integrated into the plug this makes it easier. This fixed the problem with both Freezer & Refrigerator The Temperatures returned to normal Freezer 0 degrees Refrigerator 37 degrees I also checked out the refrigerator side Condenser I noticed only that the Condensate pan was starting to rust so I will remove it and use some Muretic acid to clean it up and then spray it with some Cold Gavanize with Zinc you can get this spray paint at Home Depot it seals and prevents rust. Or you can order a new one for about $ 16 bucks but it will start rusting just like the old one did eventually if you do order a new Condensate Pan I suggest spraying it before you reinstall it so that it will not rust. Greg H. Eldorado, AR

First I turned the refrigerator and water line off. Then moved to the freezer section, followed the directions, removed the two screws. Directions state to not remove them but I had to in this case. Unplugged the ice maker and removed it from the freezer. I installed the two mounting screws then tried to plug the electrical connection back in but had to use the adaptor cord furnished in the kit. The cord was a little long but I tucked it in and mounted the ice maker. Turned it on then turned the refrigerator and water back on and in a few hours had ice! Very easy to do!