TFX24ZFB General Electric Refrigerator - Instructions

Replaced both upper and lower cam's. Removed door from refrigerator, removed bolts on door cam on bottom of main door and replaced cam, then removed bolts from door hinge assembly, drilled out rivet holding on cam, replaced with new cam and re-riveted.

Laying on the floor I blocked up the door. Removed old hinge and cam. First I replaced the cam then I inserted the hinge into the cam. Positioned the door to enable me to refasten the hinge to the Refrigerator. Another way is to empty the stuff from the refrigerator door.Then remove the top hinge take off the door and place it on the counter on a blanket so as not to scratch the door. Replace the cam. Place the door back on the wooden blocks.Insert the Hinge into the cam while the door is standing on the wooden blocks. It would be a great help if you had a second person to hold the door so you don't gets bumps on your head. You first need to attach the top honge withe the 2 screws loosly so the door will move. Then screw the bottom hinge to the refrigerator. If you find that the inside of the door is rubbing lossen the top hing and adjust the door until it closed properly. Also by putting the stuff back on the door may cure the rubbing. Good Luck

Removed refrigerator door and replaced bottom door pivot with the included mating cam and the door closing cam on the bottom of the door.

I didn't know that there were two mating cams and only ordered the door closing cam which I read online was the problem. It was the number one part on the part select list. The number two part was a kit including the door closing cam and the pivot with mating cam attached. It would have been helpful if there had been some notes that said check condition of both cams before ordering the part. So I have a spare door closing cam and paid an extra $19 including $8 shipping which negated a return.

The repair is easy - getting the right parts the first time is the trick.

Remove screw at hinge cover, top of door.
Remove two screw/nuts at hinge and remove hinge while holding door in place.
Lift door off of lower hinge
remove two nut/screws at bottom of door and replace closing cam. Be sure the pivot pin hole in the cam is lined up with the hole in door.

Next drill out rivet holding cam to lower hinge on the refer. Install cam with a pan head screw and nut (to replace rivet). It will help if you remove the plastic grille cover at the bottom of the frige.

Set door back on the lower pin and shut so the the magnetic strip holds the door in place. Re-install the upper hinge loosely. Adjust the door for an even gap and tighten the screw/nuts. Re-install the cover.

A very easy fix.

Thought I would only need one when I looked at the picture of the parts. Decided to order two just in case and after taking it apart both were broken. Needed two.
Took the top door bracket off and lifted the door off of the bottom bracket. Re-assembled cams, put a little white grease on all moving parts, placed the door into bottom bracket and installed top bracket. Adjusted top bracket to make door line up with edge of refrigerator and all is well.

Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH

Removed screws holding top door hinge. Lifted the door off bottom hinge. Unscrewed cam from bottom of door. Drilled out rivet holding the second cam in the bottom hinge. Replaced both cams using a flat headed bolt to hold the bottom cam. Dropped door into bottom hinge and replaced top hinge screws. Job done.

Make sure you buy two cams and have a bolt to replace the bottom rivet.

Not a difficult job as long as you have a drill !!!

I first removed all of the door contents. I then removed the door from its mountings by removing two screws at the bottom bracket. With the door lying on the floor I then removed the two screws holding the door cam assembly in place. I inserted the new door cam, then reversed the process replacing the four screws.

I took the top over off the pivet bracket and used a nut driver to remove the screws on the pivet. Lifted the door off and put on some saw horsess. I revoved the pieces of the old cam on the door by taking out the screw and put the new cam back.
I then drilled out the rivet on the bracket on the door and removed the broken cam. replaced it with the new one and used a screw and nut to replace the rivet. Put the door back and works great now.

Followed previous poster's steps. Replacement of door closing cams took 35 minutes. Make sure you buy 2 cams for each door.

I popped the rivet of the new hinge I received, removed the plastic bushing and installed it on my old hinge - this was the part that went bad on my old hinge. I re-installed my old hinge with the new bushing, problem solved

I did not realize I needed 2 cams to complete repair. Door cam was riveted in. I had to drill out rivet and replace with nut and bolt. Otherwise it went quite sommothly. At first I just replaced the cam on bottom of refridgerator but door was not quite right when closing. Further inspection showed the door had the other half of cam that also needed replacement. Needed 2 orders. Paid for 2 shippings.

removed the door, installed the cam riser, and reattached the door. It took longer to remove the contents in the door than it did to install the cam riser.

Your vidio was Brilliant !!i just followed your instructions

Took the door contents out and put them on the counter, took the door off the hinges by unscrewing the 2 screws on the top of the Fridge and lifting the door off the hinge onthe bottom. Then laid down the Fridge on the kitchen floor and replaced the Door Closing Cam, keeping in mind the order of the 3 shims and other things on the bottom of the door. Simple.