GSE25ETHBCC General Electric Refrigerator - Instructions

First, I turned off the water supply line to the refrigerator from the house at the wall and unplugged the power cord. Secondly, I removed the small screws that hold the piece of cardboard over the opening in the lower left corner (rear of the refrigerator) by the compressor. Thirdlyl, I removed the other end of the water line where it attaches to the water valve with an adjustable end wrench. Then I removed the small screw that holds the double water outlet valves to the refrigerator frame. I then removed the water valve by pulling it out of the rear of the refrigerator, unplugged the electrical connections, and cut the water lines where they enter the valves. I then plugged the electrical connectors into the new valves and pushed the hoses into their respective openings. These are one-way connectors - once you push them in (firmly) they will not leak or come back out. All I did then was replace the valve and secure it with the one little screw and then replace the cardboard piece onto the rear of the refrigerator. Don't forget to turn the water supply back on. That's it!!

pulled out refer. found leak at corner lower back, pulled off lower cover. found valve for icemaker leaking. looked in owners/inst guide, pulled up on computer, identified part, called, order overnight part. recieved part & installed, repair complete & successful.

We soaked the new gasket in warm water for a while and we pressed it into place. Really very easy. Working fine again.
Thank you!

Your instructions were "spot on"! Pried out broken switch with screwdriver-reinstalled new switch. Very easy! Ordered on line on a Wednesday new part arrived on following Saturday-Great service and will definately use again. Highly recommend PartSelect!

Before replacing the top filter housing, ensure the inlet water valve is operational. Replacing is a straight forward process. Unhook the houses from the inlet water valve in the back of the refrigerator. Remove and replace the top filter housing and ensure you replace the sealant using plumbers putty or sealant dicor butyl putty.

the only thing I had to do was slide the shelf in.. but this website saved me over $50 on the part (I got a price from my local appliance store of $80.00 and 2 weeks to get it)

Removed the plastic frame by pushing to the inside (all 4 sides), removed touch pad by sliding it to my right and disconnected the wires. Removed the four screws that hold the dispensing unit and replaced broken parts. Please note that I also replaced the funnel. Total cost of repair for DIY $30.00, savings by avoiding repair man, priceless.

Shut off water supply. Unplugged refrigerator. Removed cover. (6 screws -- nutdriver will come in handy). Removed screw securing water valve to frame (again the nutdriver). Unplugged red and white power connectors to solenoids. Using channel locks, loosened nut holding main water supply to valve and removed. Depressed compression fittings to valve and pulled out plastic water lines that supply water dispenser and ice maker. Reconnected main water supply to new part. Pushed both water lines into respective fittings of new part. Reconnected power supply to solenoids. Attached new part to frame with screw. Replaced back cover. Turned water supply back on. Plugged refrig. back in. Problem solved! Savings = $300!

Remove rear plate. Remove fan bracket. Replace fan gaskets, blade and motor. Replace bracket. Replace rear plate. Very simple. Fixed the problem.

1. Slide out refrigerator away from wall.
2. Unplug refrigerator electrical cord.
3. Slide out refrigerator further to be able to get in back of.
4.Turn off water control going to refrigerator.
5. Clear top shelf around water filter area, remove water filter.
6. Remove water filter cover housing lid by lifting off.
7. Using a ¼" nut driver, remove two screws attaching water filter housing.
8. Go to back side of refrigerator, & remove 2 screws from the silver cover plate of MWD manifold water line unit.
9.Using ¼" nut driver, remove lower cardboard cover that protects the motor & fan area.
10. Clean motor & fan area with old tooth brush gently, & vacuum dust off.
11.Using (2) ½" open end wrenches, loosen & remove both water lines.
12. Go to front inside of refrigerator. Gently pull out old water line manifold assembly, you may have to twist it some to get the protective sleeve out of the hole.
13.Insert new water line manifold assembly into the hole, when it gets to mostly in, gently work the protective sleeve through the hole.
14.Position the new manifold water filter housing into place & reinstall 2 screws. Do not over tighten.
15. Go to back side of refrigerator, gently push down on protective sleeve so you then can replace silver cover with 2 screws. Do not over tighten.
16. Remove old tape that was originally holding water line tubings.
17.Connect water lines to water supply lines, using (2) ½ " wrenches. Tight, but not over tight.
18. Re tape water lines to back of refrigerator, using a strong tape like duct tape in an orderly fashion.
19. Turn on water supply, check for leaks.
20.Re install black cardboard piece on lower end of refrigerator.
21. Plug in refrigerator.
22. Install water filter inside of refrigerator. Install cover over filter housing.

Instructions say run capacitor is by motor, but on this frige its in the refrigerator compartment. The capacitors looks different, one square and the other long

I pulled-out & unplugged the refrigerator. Removed the screws to gain access through the lower back panel. The water valve is on the left side as I face the back of the fridge. It has one screw holding it to the frame of the fridge. Once it is free, the main water hose is unscrewed and the two out-let lines were pulled-out. If your valve was not ruined prior to this, it is ruined now, as the lines will not re-seat. Then everything is done in reverse order. I did cut 1/2 inch off of the two lines so that they reseat into the new valve. Just push into the valve and they are good.

Ordered the icemaker replacement. unplugged the unit, followed the simple instructions and got it done in less than 30 minutes. It did take a LONG time to start making ice. But it's working now.

After lots of research online, i narrowed my problem down to be the double outlet water valve, behind the fridge. My biggest problem was getting the refridgerator out of its spot, but after that it was pretty simple to change. I took the cover off the bottom, in the back of the fridge, then i removed the inlet waterline (after i turned off the water supply to the fridge). After that i removed the screw that holds the valve to the framework. Now i pulled off the two other waterlines from the old valve and moved them, one at a time, over to the new valve, along with the wire harness. The rest of the instalation was reverse order. Simple fix that im glad i didn't pay an expert to do!

Replace