CWE23SSHISS General Electric Refrigerator - Instructions

Pulled out bottom crisper drawers. Removed drawer slides. Removed side plastic panels, then removed back panel which exposed the fan. Removed fan and replaced with new fan. Had to use the heat gun because there was ice buildup on left corner of rear panel. Reassembled in reverse order. There is several excellent videos on You Tube.

Removed back wall cover over coil. Defrost all ice with a hair dryer. Cut white wires and replaced Temperature Sensor. It has been working for a week and no trouble at this time. If you have this system on your GE refrigerator do this before replacing the motherboard. I must admit I was thinking that was the trouble. Motherboard was replaced after 5 years old now 5 years later my thinking is this a 5 year problem. So try the Temperature Sensor.

follow the easy instructions replace 3 temperature sensors cut the wires and crimp them with new sensor and it works like new

Purchased parts per your diagram and went to a appliance store to see how it was assemble

I followed the directions included with the water filter and it was simple. The only problem I had was not being strong enough to easily remove the old filter. I did accomplish that after a few tries and the rest is history.

I was able to repair both problems for a cost of about $6.00 thanks to parts select. Will definitely be back for more parts when I need them. Great selection and rapid shipping.

Once I received that New Part, just place the 1 Piece from the old Shelf into the New Part and mounted the Shelf in the Door.

I determined one of the five LED lights in the refrigerator was dead by swapping it with a working one. The refrigerator lights are wired in series and if one of the lights is dead the remaining ones turn on, but very dim. I called PartSelect.com and thanks to their help we determined the correct part to order which is the oval-shaped cover LED assembly which includes the cover, LED, and female connector. The part from PartSelect arrived in three days. The oval-shape LED plastic Cover assembly is mounted on the refrigerator and held by a couple of side latches. First unplug the refrigerator and then proceed to lightly pry the oval-shaped cover side facing the rear of the refrigerator with your finger nail to remove it. With the LED cover removed you can then press on the LED connector tab to slide it off. Now slide the female connector of the replacement part to the refrigerator male connector and snap the oval-shape plastic cover onto the refrigerator receptacle and then plug it back to its outlet. Now all the lights in the refrigerator should light up brightly! That's all folks. Hope this helps. Good luck. Yours truly.

I watched the video online and it said there were three sensors in the refrigerator, two in the freezer and one in the refrigerator. I only ordered one sensor and was going to try the one in the refrigerator first. He said the upper one in the freezer is the most difficult, but is usually the problem. So, I replaced the upper sensor and tried restarting the unit. Everything went well and it fixed the problem.

First, turn off power - since I did not want to pull the refrigerator out on my wood floor I tripped the circuit breaker to that circuit and opened door to make sure interior light was off (ensuring power was off). This unit has a bottom freezer, I took out all shelves, ice maker and all parts in the way of accessing back of interior of freezer section. Removed back plastic section by removing one screw in middle top of back panel and prying it out. This was a bit difficult as it was in there a bit tight but once the plastic warmed up it pulled out ok. This revealed the compressor section and temp sensor that was attached to the copper coils with of all things - a zip tie! In pictures of this that I looked at on various web sites the sensor was on a metal bracket attached to the coil so it made me wonder if tf the factory took a shortcut? I cut the old sensor wire, stripped the two wires 1/2", and connected them to the new sensor wire with butt connectors, I put some silicone into the ends of the butt connectors to prevent moisture from entering into connectors and wrapped the connection in black electrical tape. I then "attached" the sensor to the coil using a zip tie, put the plastic back piece back on, inserted everything I took out and put power back to refrigerator. It's been 3 days and temp of refrigerator is stable, ice maker not clogging up, and compressor not running all the time! So far so good.

Ordered a replacement ice maker. Simple to remove old unit one screw and one screw to remove wire cover to unplug. Replacement unit looked a little different as the left side of the new unit had various ridges which did not allow a proper fit into ice making box. After examining old unit and new I swapped the old left cover with new left cover and unit fit perfectly and it is working correctly. I suggest adding a quick note about the upgraded part as it may not fit properly and the side cover may have to swapped out.

Removed all containers from the freezer,
Removed lower freezer door, 3 bolts on each side.
Removed one front screw on the ice maker, unplugged two connectors on slide off unit
Removed covers on the old ice maker and installed on the new one
Installed the new ice maker in reverse of the removal process

Inspected the old ice maker and found the motor drive gear had missing teeth; I believe that the heater on the ice maker was failing causing a strain on the drive gears

Exposed evap defrosted with heat gun exposed defrost element defrost termination switch ok therminster didn’t check out the thermistor sends the signal to logic panel then run the the freezer ice machine and refer temps it took 24 hours before the system starting to show results freezer compartment 10 below ice compartment 0 degrees refer temp 37 degrees one refrigerant three different temps system is running at optimum performance 450.00 $ service call the thing with GE appliances there is no wiring diagram .thankyou parts select .ill use you on all domestic service calls.

It just snapped in. Fit perfectly. Excellent service.

Removed drawers, lifted out old frame assembly ( no tools ) removed and cleaned old glass from assembly.
Carefully screwed old rollers ( x4 )into new frame, then placed old glass in new frame, repositioned frame into refrigerator and then repositioned drawers in frame.
20 minutes , no issues