36369267991 General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- ED from ENON, OH
- Parts Used:
- WR2X9391
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Short in the light socket.
Un Plugged the frig. Unlocked the socket by pressing down on the latch. Pulled the socket out ensuring I had enough slack. Unplugged the old socket installed the new. Plugged the frig back in. Tested the switch . Very easy-to-use.
Was this instruction helpful to you?
Thank you for voting!
The vegie draw rack cover
Both side rails were busted. the parts were precise and it was extremely easy. Thanks again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from Charlotte, NC
- Parts Used:
- WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
socket had melted
pluged the wire harness into the new socket from the back and snaped the socket in place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Carol from Odessa, FL
- Parts Used:
- WR72X273
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
broken slide rail
removed the screws and then replaced the rails. Easy
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Don from Eugene, OR
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
The door activated light switch was missing.
Pulled the two wires out from the access hole in the lower part of the refrigerator. Put them in the spade connectors on the new switch, and pushed the switch into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Minky from New York, NY
- Parts Used:
- WR17X2768
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken part
I ordered the part one day and it was in my refrigerator by the next day. No tools required. You guys are incredible. This is the second time I ordered parts from you. You never disappoint!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from Tulsa, OK
- Parts Used:
- WR72X274
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
broken slide rails for meat bin
Slide rails are shipped without screws, therefor, must use old ones. TORX driver required for self tapping screws. Missing screw required trip to hardware store for replacement. Unable to match screw; had to improvise with a different type of screw.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- shelli from gaithersburg, MD
- Parts Used:
- WR17X2770
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
slider cracked, so drawers wouldn't stay in
The entire frame that holds the two crisper drawers pulls right out. After that, it's just a matter of unscrewing the broken part, snapping in and screwing the new part and sliding the whole thing back in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patricia from Sylva, NC
- Parts Used:
- WR23X37285
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Bad switch for door prevented interior light from coming on
Just as your video described, although due to the age of the fridge, it took a bit longer to remove the defective switch. Your video made this so simple, I can't imagine why we lived with a dark fridge for so long! I was ready to buy a whole new fridge, as repairmen are often nonexistent for small repairs. I am the biggest fan of your company & it's repair video. THANK YOU SO MUCH
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jim from warwick, NY
- Parts Used:
- WR2X8699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the kids broke the lower door bin by overloading it
looked up the part, ordered it. 2 days later, popped it in...less than 5 seconds...DONE....great website and customer service....very descriptive and informative for the novice and experienced repair person alike.....Thanks!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edward from Pembroke, MA
- Parts Used:
- WR2X8700
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bottom of door shelf right end cap broke
Very simple snap out and snap in. Very simple
Was this instruction helpful to you?
Thank you for voting!
broken vegie bin slide rails
This was very easy. Just unscrew the broken side pieces and attach the new ones. If the rubber gaskets are still in good shape, gently pull them off and attach them to the new rails. I was very impressed with the service from Partselect.com. I gave them my appliance model number and they helped me find the right part. I ordered on Sunday evening and had the parts in hand by Tuesday. Great service! I will definitely use this company if I need more parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Patrick from Columbia, MD
- Parts Used:
- WR2X8699
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
broken part
snapped it on the metal cross bar. Your website was great for finding the right part!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from Prospect, CT
- Parts Used:
- WR17X2769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
the side rail broke because I kicked it
I took out all the stuff on the shelf, and the drawers.
then I took out the shelf, pulled off the cover so I could get at the screws.
I unscrewed 2 screws, threw out the old part, and screwed the new one into the shelf.
then I put the whole thing back together, in total the hardest part was cleaning off the shelves and then putting everything back in.
As a note, there was a gasket on the old rail that was not on this one. I had some silicone tabs that I used instead, but I really think the gasket should have been part of the order.
then I took out the shelf, pulled off the cover so I could get at the screws.
I unscrewed 2 screws, threw out the old part, and screwed the new one into the shelf.
then I put the whole thing back together, in total the hardest part was cleaning off the shelves and then putting everything back in.
As a note, there was a gasket on the old rail that was not on this one. I had some silicone tabs that I used instead, but I really think the gasket should have been part of the order.
Was this instruction helpful to you?
Thank you for voting!