36369267991 General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Irma from Tylertown, MS
- Parts Used:
- WR17X2769
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The front of theDrawer Slilde Rail broke off the rail.
Removed the 2 drawers and then the glass shelf.
Positioned the drawer slid and tightened to rear screw and the front screw.
Replaced the shelf and the 2 deawers.
What's the big deal? Any 78 year old woman can do it.
Positioned the drawer slid and tightened to rear screw and the front screw.
Replaced the shelf and the 2 deawers.
What's the big deal? Any 78 year old woman can do it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- robert from Vicksburg, MS
- Parts Used:
- WR9X520
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Wrench set
Water Leaking out of bottom of refrig first then out of vegetative bins underneath
Replaced defrost thermostat and defrost controller and also noticed that run capacitator for compressor almost oxidized in two and ordered and replaced and cleaned out drain tube and invertor (which was blocked by frozen peas and other food)or water to drain during defrost cycle and put everything back together and seems to work fine now....storing beer in outside refrig now
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Beverly from Pensacola, FL
- Parts Used:
- WR17X2770
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
the plastic part had broken and wouldn't support drawer
Replacing the new part wasn't hard, just very time consuming and frustrating. I had to remove two-thirds of the shelving of refrigerator as broken drawer slide was on the bottom and I had to have room to remove old and replace new. Of course, then I had to CLEAN all the drawers and shelving before replacing them and then, because they were fresh and clean, I had to remove the other third of shelving and wash and replace it. So, it was an hour-long or more time. I love your business, and had no idea I could get so many parts for old applicance and replace them myself, and I am a 70-year-old woman! This was the 2nd time to use your site and I will return to it again when needed. Thanks for prompt and reliable service and a site that makes it easy for a neophyte like me to find the broken part ! Keep up the good work.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lawrence from O'Fallon, IL
- Parts Used:
- WR24X446
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
bottom of gasket deteriorated and let in warm air
i pulled the old gasket off, and placed the new one in place, starting at the corners. then i lined up the insert in the gasket with the gap where it is to go and ran my fingers along the gasket, pressing in with my thumb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- tara from cumming, GA
- Parts Used:
- WR24X446
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
needed to replace the gasket because it had become brittle
My husband thought he would have to set aside time on the weekend to replace the gasket. It was delivered and I unpacked it put it on and that was that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paypal_shipping_address from Ripon, CA
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Light would no longer turn on
I watched the video online, followed the instructions and within minutes had the part installed. The frig light was working once again! I will say the original switch was very snug and I had to do some very minor scraping of the plastic to get the new part to slide in.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jodi from Benton Harbor, MI
- Parts Used:
- WR23X37285
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Light out
Turned off the breaker to the fridge because I couldn't reach the power plug to unplug it . Use small flat head screwdriver to pop out the piece, disconnected the rubber prong connectors, inserted the new piece into the rubber prongs snapped it back into place. Flipped the breaker back on and prayed it worked. It did and I saved myself $120 service call.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Herbert from POCONO LAKE, PA
- Parts Used:
- WR60X10168, WR02X10098
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
the condenser fan motor was intermittently verynoisy. obvious sign of a (possibly imminent) failure
1 unplug the appliance
2. remove the rear cardboard cover, giving access to the compressor and condenser area
3. remove the two (condenser motor bracket) mounting screws, then with the motor assembly in your hand remove the the fan blade which is friction mounted to the motor shaft( note the exact position of the fan blade on the motor shaft so you can replace it in the same position when you reassemble), remove the two wires connected to the motor. Also remove the rubber resilient mounting grommets on the motor mount frame as these can harden with age and cause excessive vibration.
4 install the new motor into the mounting frame with the new grommets
5 reconnect the two wires to the new motor (non polarized)
6 secure the mounting frame (with the installed new motor) back in place
7 slide the fan blade onto the new motor shaft
8 screw the rear access panel back in place
plug in the refrigerator. the next time the compressor and condenser fan cycle on, verify operation of the new condenser fan motor
2. remove the rear cardboard cover, giving access to the compressor and condenser area
3. remove the two (condenser motor bracket) mounting screws, then with the motor assembly in your hand remove the the fan blade which is friction mounted to the motor shaft( note the exact position of the fan blade on the motor shaft so you can replace it in the same position when you reassemble), remove the two wires connected to the motor. Also remove the rubber resilient mounting grommets on the motor mount frame as these can harden with age and cause excessive vibration.
4 install the new motor into the mounting frame with the new grommets
5 reconnect the two wires to the new motor (non polarized)
6 secure the mounting frame (with the installed new motor) back in place
7 slide the fan blade onto the new motor shaft
8 screw the rear access panel back in place
plug in the refrigerator. the next time the compressor and condenser fan cycle on, verify operation of the new condenser fan motor
Was this instruction helpful to you?
Thank you for voting!
Left drawer slide broken replaced both right and left
Removed drawers and glass shelf. Removed screws that hold old slide rails in place. Installed new rails and re-installed cover for vents. Placed assembly back in and installed drawers.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joy from BELMONT, NH
- Parts Used:
- WR24X446
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
water build up in bottom of refrigerator
Allow 24 hours for new gasket to flatten out from packaging. Gently peel off existing gasket. Clean dirt and mold from mount area.
Mount gasket beginning at a corner. Press gasket into place every inch around perimeter. Done! Water is no longer in bottom of refrigerator and it is running more efficiently (less time running) due to the fact that it can maintain the temperature for longer periods of time.
Mount gasket beginning at a corner. Press gasket into place every inch around perimeter. Done! Water is no longer in bottom of refrigerator and it is running more efficiently (less time running) due to the fact that it can maintain the temperature for longer periods of time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from DEPEW, NY
- Parts Used:
- WR60X10030
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Broke fan blade cleaning unit
Ordered part came in 3 days. Removed plug and rear cover. Pulled off old fan . Installed new fan by pushing it on to shaft. Plugged unit back in to check operation, installed rear cover. Done. Part fit perfect. Thanks to this site you folks are great !
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marj from NEWBURY PARK, CA
- Parts Used:
- WR2X9391
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Fridge light dead even with new bulb
1- youtubed the potential diagnoses, 2- resourced and ordered parts, 3- removed old socket, installed new one :-)... My fridge is an older fridge and could've used a screwdriver for eyeglasses. Plug and play easy... YAY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- philip from FARGO, ND
- Parts Used:
- WR24X445
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
had moved into new house and discovered freezer door gasket incompletely sealing tried using home warranty service but decided trying rather than 100$ service fee. ordered gasket and watched several u-tube videos.
Placed new gasket into dryer,( recommended by 2 u tubes) high heat for about 10 minutes and was a snap getting softened gasket into little tiny slot actual placement was done twice as there was a twist in the seal i missed the first time so did do twice but was so easy this way was almost sad thinking it would have been 100$ deductible having someone do it and who knows what normal cost would have been......thanks u tube
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Loren from EL PASO, TX
- Parts Used:
- WR23X37285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
40 year old refrigerator brittle light switch fell apart
with a jewelry screwdriver I pried the lock tab in and pulled switch down carefully, the hardest part was that the power wire connector was stuck on good but the pliers and the jewelry screwdriver was its match for a bout 5 minute for one connection a simple pull off prong connection. After the wire connected back to switch it popped back in SNAPP
Was this instruction helpful to you?
Thank you for voting!
BROKEN HOOKS ON BOTH ENDS OF THE REFRIGERATOR DOOR SHELF
ATTACH ENDS TO CENTER BAR. HOOK INTO SLOTS IN REFRIGERATOR DOOR.
Was this instruction helpful to you?
Thank you for voting!