TFK25PRYAAA General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Richard from University Place, WA
- Parts Used:
- WR17X3489
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken part due to age
Super fast replacement, and the part was sent to us FAST and WELL-PACKAGED and REASONABLY PRICED! Thankyouverymuch!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- VINCENT from SPOTSYLVANIA, VA
- Parts Used:
- WR17X3489
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Tab that holds light shield was broken off.
Removed ice tray and set on kitchen counter .One small phillips scredriver to remove broken tab.
Attached replacement shield with screw, replaced ice tray. Probaly total of 5 to 10 minutes to find scredriver, do the repair & replace screwdriver where it belonged. Took more time to place order then do repair. Add a couple of minutes to unpack.and some more time to drop off cardboard box at recycle center.
Attached replacement shield with screw, replaced ice tray. Probaly total of 5 to 10 minutes to find scredriver, do the repair & replace screwdriver where it belonged. Took more time to place order then do repair. Add a couple of minutes to unpack.and some more time to drop off cardboard box at recycle center.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JAMES R. from INDIAN SHORES, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Moisture seeping into freezer through ice dispenser
Removed ice dispenser trim from bottom-up and then removed control panel by gently pulling up from the bottom. Removed four screws holding dispenser chute and then two screws holing flapper assembly. Replaced gnarly old flapper with a new one and put all removed pieces back together.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Lewis Center, OH
- Parts Used:
- WR71X2494
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frame Was Broken
Took off metal brackett, removed plastic frame and installed new plastic frame.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Earl from Franklin, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The door recess asm would not seal tightly
remove the 'pop-out " frame around the door recess, you pry the flexable seal from around the ice despenser, have someone hold the unit with the wiring, remove the one screw that holds the door recess, and replace the new one. reverse the procedure. remember to unplug thr frig. first
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- john from milford, CT
- Parts Used:
- WR30X256
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken ice bucket
Very easy to repair-Went online-Found diagrahm-Ordered part-and presto it was fixed.
Very good schematic to go by. If you can read you most likely can fix it.
Very good schematic to go by. If you can read you most likely can fix it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lawrence from new haven, KY
- Parts Used:
- WR17X4358
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
water tank was leaking
really simple,take 2 nuts loose pull the hose out and then replace.took less than 30 minutes
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Bridgewater, NJ
- Parts Used:
- WR17X3089
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Ice dispenser had a transistor failure on the control board
The solenoid in the dispenser was overheated due to the control board failure. After I rerplaced the board I found the heat had distorted the plastic crank and jammed the solenoid action. The plastic crank was easy to replace. Now after expending approx. $75 everything works normally!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- alfred from holyoke, MA
- Parts Used:
- WR17X4358
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable), Wrench set
pinhole leak in water resevoir
pulled fridge away from wall, shut water to fridge disconnected both lines,back one and front one.Removed old water resevoir 1 screw. cut old lines at resevoir. used small threaded rod (1"long)to connect old lines to new lines and taped together,pulled new lines with old lines and reconnected.No lifting of fridge,actual repair under 1 Hour but took longer because I cleaned underneath really well and took my time.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Saint Johns, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Frost in ice dispensor
Had to take front panel off dispenser area. Then remove components and install new part. That was easy part. Problem was getting components back into front of freezer. Seemed like something was blocking it from going all the way in. Had to remove small amount of insulation and "jiggle" components and eventually fell into place.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Frank from Novi, MI
- Parts Used:
- WR17X11349, WR17X4358
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
My despenser water reservoir leaked at the seam, causing water to alway puddle at the bottom of the inside space
I had read from your sight, to simply cut the lines at the reservoir and tape the new lines to the old. Then use the old lines to pull/feed the new lines to the coupler/valve. This worked great and greatly decreased the time it took to install. I spent more time moving out the frig and cleaning up all the dust (probably should do that more often)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Wilmington, NC
- Parts Used:
- WR17X3489
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Broken Freezer Light Shield
Remove ice maker bucket. Unscrew single screw in center of shield, take out shield. Insert new shield, making sure the 2 tabs on the shield are slid into mount from the left, center the shield so center tab is aligned with screw hole, Tighten screw, replace ice bucket. SUGGESTION: This would be a good time to replace light bulb!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Pasadena, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice/Water dispenser freezing/clogging
I followed the Video on your website and that made it so easy and simple to follow. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dennis from Glendora, CA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Inside freeze was frosting up
used a flat screwdriver to pop off out side cover then remove 6 screws took off plate. Pulled off the flapper and replaced. less the 15 mins and fixed the issue
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THEOTIS from CHARLOTTE, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Refrigerator COnstant running and low ice output
I followed the instructions on the youtube video on the company web page. I removed the cover by hand, removed the exisitng flapper door and install the new door, easy as pie.
Was this instruction helpful to you?
Thank you for voting!