PDSF5NBWAWW General Electric Refrigerator - Instructions

followed part select video instructions

What an awesome site! After putting in my model number and finding the problem I was having, I simply picked the 2 parts that were most likely to solve the problem. I bought a defrost thermostat, and defrost heater. To a high certainty, they would solve my problem. They didn't however! I ended up having to buy a temperature sensor on another order a few weeks later when the problem resurfaced! My own fault. I should have bought it the first time. As others have written: the longest part of the job is defrosting the ice from the coil. One thing I did that I didn't see suggested: plug the drain hole below the coil. I put a couple towels in the bottom of the freezer and ran the hair dryer. Didn't take long. I read that the amount of water created will overflow the pan under the refrigerator, so I plugged the drain hole. Once you clean that mess up, the repair is pretty straight forward. Great site. Even through I had to make two separate purchases, I still saved a lot of money. Thanks!

Followed the video instructions with the help of a young man who worked on trailer hitches before and knew how to splice wires. Beware of splicing the wrong fan motor back into the assembly. . . . That happened here and we had to start the splicing all over again with the correct fan motor.

I followed the video provided by PartSelect, very helpful. I had to cut and splice 4 wires. The repair was successful. The replacement part was an exact duplicate of the original. I still notice the same sound but one tenth the volume. I hope the problem does not return. Many thanks to PartSelect for information to identify the problem and prompt shipping of the repair part.

Parts were perfect. Shipment great. It took a bit of time to get back to the Evaporator fan, so i basically had to take the entire freezer apart. Not a problem. The one issue i ran into was my unit had 2 white wires which connected to a silver bullet thing, that were not included in the wiring harness. Maybe I could have ordered that part (thinking out loud) I had to cut the old one apart, and adapt them into the new one, which had 2 holes to spare for this purpose. I guess i could have spliced every wire, but didn't. The freezer now SOUNDS LIKE A FREEZER. Thanks,

Watched Partselect video. My unit was different. Took out all shelves. Removed ice pan. Removed unit which turns auger in ice pan and metal side supports. Removed plastic side tracks which support ice pan. Removed ice maker. Removed light sheild and bulbs. Removed lower coil cover.(4screws) Removed remaining cover which covers fan. Removed bottom fan support bracket(one side only) Removed fan blade by holding shaft, twist blade off. Push cover up out of the way. Cut four motor wires on old and new motors, leave enough lenght to splice with but conectors on wires, wrap four conectors with elect tape, install two new motor support grommets, fan blade, and everything else in reverse.

First, I had to remove the freezer drawer front. This is 8 large phillips head screws. then remove the plastic cover over the drawer slides. to do this, remove the white center screw from the slide near where it attaches to the drawer front. then the plastic cover will slide off pushing to the rear of the slide. take off the slides from the freezer walls by removing the phillips screws and pulling them towards you. They have tabs/slots in the rear. remove the center tray support and support bars, too. the icemaker has to come out, that is just 2 phillips screws but you also have to disconnect the electrical connector. just squeeze the locking wings and rock/pull. a screw in the top center of the back panel comes out. Lift and pull the back panel out. The evaporator coil appears. The thermocouple is attached to the coil in the upper right. Cut that one's wires and take it out. Just cut back about an inch from the back of the thermocouple, there is not much slack. Seperate and strip the wires back about 3/8 inch. Do the same for the new thermocouple. I twisted the wires together and used a solder sleeve to join the wires. The sleeve is just a little plastic tube that has a ring of solder in it that melts with heat gun heat. You can join the wires using butt connectors or whatever method appeals to you. I just wound the extra wire and put a cable tie around it, there is plenty of hiding space in that area. Make sure the new thermocouple is contacting the coil firmly.At this point, for a test, I left everything apart, propped the drawer against the opening and plugged the fridge in. Note that the evaporator fan will not start spinning immediately! It will just sit there making little bumps like it wants to go. The temp in the coil has to get settled before the electronics in the refridge will tell the fan to spin. It takes maybe 20 minutes. Reassemble. Fridge and freezer work great. It does take several hours for all to get cold again.

Very limited working space in this model. Must remove grill and disconnect elect connector on motor. One additiional tool suggested: Extendable rod with magnet on end because you will most likely drop something. First, remove two screws holding motor to metal strap. Tool must be inserted between blades of fan in order to get to the screws and this is the hard part. Fan and motor are removed as one assy and this takes some manuvering. Might have to remove front screw on metal strap to gain more room. I did not attempt to remove fan shroud. My fan was attached to the motor shaft with a metal clip. Spray a good lubricant such as PB Blaster on the shaft, wait a few minutes and press it or tap it out gently. Save misc parts on old motor for reassembly. Your set up may be different so check out everything before starting.

about an hour to figure out what was causing the vibration and noise and about an hour to put it back together and 5 min. to order a new fan blade thank you.It started making noise during thanksgiving dinner so we toke it apart after dinner and I cut the other 2 blade to match the broken one so to cut down on the noise and vibration semi put it back together and 7 days later the part arrived.

as per video- follow all of the videos and u r going to save a lot of money tx partselect im glad I found u guys ps only order from partselect.com they only ship the correct parts remember look at the video select the symptom and buy as per video tx again problemsolved

The repair is a snap, you can watch the video and it will put you on the right path. My story is more about the service that Part Select gave me. I used a small box fan on low as a temporary fix. My model number was worn off from the box wine we store in that particular place. So I ordered the part based on looks, well it was wrong. Called Part Select and we talked, the nice lady on the other end said OH it must be this fan motor. Send us back that one, and I'll get this out too you. I'll credit your account for $7.99, and it cost me $8.99 to ship back the wrong part. Wow, the next day I received the new motor. They sent it overnight! I thought it would be 5-6 days! Unbelievable. I will use this company for any, and all my repairs.

killed power-gently pried out old switch using two screw drivers-replaced faulty switch-and tested OK.

I decided to replace motor and fan, having previously altered/trimmed the fan which stopped the howling but caused a vibration. Unplug from mains. Clear out two top shelves in freezer. Remove light cover. Remove two screws(1/4 driver)at top of steel panel in rear of compartment and let it drop. Remove two screws above light. Pry up section above light/fan housing to access two screws retaining the light/fan assembly, loosen screws sufficiently so that assembly can be lifted and removed. Disconnect wiring plug by pinching in the sides of the plug and pulling out. Pull fan off motor shaft. Remove two screws clamping motor. Cut cable tie and molded wiring grommet to free wiring. The existing light wires can be removed from the old plug by carefully cutting around the old plug to free the pins and then pushing the pins into the new plug. Reverse procedure to assemble.

per your instructions

Removed mother board and replaced. Working fine now