TFX22JABEWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Greg from Island Park, NY
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
I complained to my wife that she wasn't closing the door all the way. My buddy found a torn washer on the floor and we discovered the riser cams (both) worn torn apart
Not really sure of the age of this fridge, as we bought the house 2.5 yrs ago.
I'm one who if it can go wrong, it will, so not realizing how stable the door was from just having the top hinge and the magentic gasket, I declined to prop the door up on blocks the way some guys say the did, and instead removed the top hinge and lifted the whole door off the bottom hinge. I traced the outline of all parts with a felt pen before removing them, figuring I'd need witness marks to help with realignment after the install.
Nut driver might've been an easier choice than the socket set, but the only ones I have a brittle and I've broken the 5/16"...
All parts came out/off easily. The new bottom hinge and the old top hinge (both on the fridge side) practically aligned itself right on my marks, and the new cam (door side) just needed to be held while the screws were tightened. I used the extensioni rod off the ratchet to drive the screws most of the way (making a nutdriver out of it).
Parts were exactly as advertised, although there was a note in the package that stressed the need to replace both parts at the same time due to material differences in the original and replacement parts. Since the cam is sold separately without the hinge, it would be good for the website to reflect that before the purchase is made. Also, even though it was only the cam on the hinge and not the whole hinge that needed to be replaced, I could've bought hte two cams separately and drilled out the rivet as another person had done, but for the $5 difference in cost, why bother?
Door now closes itself as designed, albeit slower than the freezer side, but the Wife says it always did that.
Also interesting that when first assembled, the door DIDN'T close itself at first... not sure it it needed to wear a litle, or if it just needed the added weight of having items back in the door shelves.
Love the great website... just typed in the model number and the parts I needed, complete with drawings to make sure, were right there. Great UI.
I'm one who if it can go wrong, it will, so not realizing how stable the door was from just having the top hinge and the magentic gasket, I declined to prop the door up on blocks the way some guys say the did, and instead removed the top hinge and lifted the whole door off the bottom hinge. I traced the outline of all parts with a felt pen before removing them, figuring I'd need witness marks to help with realignment after the install.
Nut driver might've been an easier choice than the socket set, but the only ones I have a brittle and I've broken the 5/16"...
All parts came out/off easily. The new bottom hinge and the old top hinge (both on the fridge side) practically aligned itself right on my marks, and the new cam (door side) just needed to be held while the screws were tightened. I used the extensioni rod off the ratchet to drive the screws most of the way (making a nutdriver out of it).
Parts were exactly as advertised, although there was a note in the package that stressed the need to replace both parts at the same time due to material differences in the original and replacement parts. Since the cam is sold separately without the hinge, it would be good for the website to reflect that before the purchase is made. Also, even though it was only the cam on the hinge and not the whole hinge that needed to be replaced, I could've bought hte two cams separately and drilled out the rivet as another person had done, but for the $5 difference in cost, why bother?
Door now closes itself as designed, albeit slower than the freezer side, but the Wife says it always did that.
Also interesting that when first assembled, the door DIDN'T close itself at first... not sure it it needed to wear a litle, or if it just needed the added weight of having items back in the door shelves.
Love the great website... just typed in the model number and the parts I needed, complete with drawings to make sure, were right there. Great UI.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- james from dothan, AL
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
The door hinge assembly at the bottom of the door was broken.
removed the door hinge assembly & replaced it with the new assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- debbie from dublin, OH
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Socket set, Wrench (Adjustable), Wrench set
hinge broke, and door would not remain closed
Part was easy to find on website. Part was delivered quickly. Reapir was easy, just replaced old hinge with new hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- richard from bayville, NY
- Parts Used:
- WR02X10140
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
cam britle door down to metal
remove plastic top hinge cover then twoscrews holding door with door closed it rested against freezer door then lefted off door put on flat surface remove tow screws at bottom of door installed new cam
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lorrie from Russellville, AR
- Parts Used:
- WR13X10020
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers, Socket set
Door dropped. Cam riser was gone
Emptied the refrigerator door so it was easier to take off. Used a screwdriver to remove the screw on the top hinge. Lifted door off bottom hinge. Laid the door down so I could take the bottom hinge off. Removed worn out parts and placed the new one on. Slipped door back on hinge,made sure it would close properly and was lined up with freeze door. Put top hinge back in place. Done!! Now door finally shuts on its own again!!! EASY!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Lake Elmo, MN
- Parts Used:
- WR51X10101
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers
Frigerator side did not cool
1 Unplugged Refrigerator and removed all the freezer shelves.
2. Removed the light bulb in the back of the freezer.
3. Removed rear panel on back wall of freezer. I had to do some defrosting on the back panel due to frost build-up.
4. Defrosted cooling coils using a hair dryer. This took a considerable amount of time due to frost build-up. Also, there was a considerable amount of water run off due to melting. I plugged the drain, and used towels and a bucket to soak up the water.
5. Removed the old element located at the bottom of the cooling coils and removed the wires from each end.. At that time, I also notice when the directions referred to "right" and "left", the point of reference was from looking out of the unit (not facing the unit).
6. Reroute the pink wire on the left side to the right side of the freezer coil. The defrost heater element I removed was a single heating element and the element I purchased was a double heating element. I then attached the blue and pink wires to the right side of the heating unit. (The pink wire was sufficiently long to reach the element. I did not need to splice an extension into it). The yellow "jump" wire was on the left side of the heating unit.
7. Attached the new heater to the freezer coil framing with the two screws.
8. Reinstalled the back freezer panel.
9. Reinstalled the freezer shelves.
10. I plugged in the unit to restart the refrigerator.
The defrosting took a considerage amount of time. Otherwise would have taken about 30-45 minutes.
2. Removed the light bulb in the back of the freezer.
3. Removed rear panel on back wall of freezer. I had to do some defrosting on the back panel due to frost build-up.
4. Defrosted cooling coils using a hair dryer. This took a considerable amount of time due to frost build-up. Also, there was a considerable amount of water run off due to melting. I plugged the drain, and used towels and a bucket to soak up the water.
5. Removed the old element located at the bottom of the cooling coils and removed the wires from each end.. At that time, I also notice when the directions referred to "right" and "left", the point of reference was from looking out of the unit (not facing the unit).
6. Reroute the pink wire on the left side to the right side of the freezer coil. The defrost heater element I removed was a single heating element and the element I purchased was a double heating element. I then attached the blue and pink wires to the right side of the heating unit. (The pink wire was sufficiently long to reach the element. I did not need to splice an extension into it). The yellow "jump" wire was on the left side of the heating unit.
7. Attached the new heater to the freezer coil framing with the two screws.
8. Reinstalled the back freezer panel.
9. Reinstalled the freezer shelves.
10. I plugged in the unit to restart the refrigerator.
The defrosting took a considerage amount of time. Otherwise would have taken about 30-45 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Zhongjiang from League City, TX
- Parts Used:
- WR51X10101
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers
Bad Defrost heater caused ice built up on evaporator, freezer not cooling enough
1. Opened rear panel of freezer, exposed the evaporator which covered with ice. Using warm water to melt down the ice, and found the bad heater.Reinstall the rear panel, the referigerator working again, without the heater.
2. Ordered the defrost heater from you.
3. 4days later, the heater assembly arrived. I opened the rear panel of freezer again, replaced the heater. The problem fixed.
This is the second time to replace the heater assembly. GE stuff looks like not very good quality.
2. Ordered the defrost heater from you.
3. 4days later, the heater assembly arrived. I opened the rear panel of freezer again, replaced the heater. The problem fixed.
This is the second time to replace the heater assembly. GE stuff looks like not very good quality.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martin from Lady Lake, FL
- Parts Used:
- WR51X10101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
freezer wouldn't defrost/causing the refrigerator not to cool
Used a hair dryer to defrost the freezer so I could replace the Defrost Heater Harness Kit, that was real easy just fellowed the directions, this seem to help to a degree but I still had to call for service to replace the defrost sensor & the defrost limit switch in the freezer, since this is under my warrenty contract, now the freezer shuts down for a period of time, allowing for a defrost cycle
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dale from Leesville, LA
- Parts Used:
- WR51X10101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
Would not stay cool
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wire
bigwill360
bigwill360
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brant from Heber Springs, AR
- Parts Used:
- WR51X10101
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
freezer was frosted up and refrigerator was not cool
The replacement heater was a dual heater instead of the single. This will be much better. The wires are long enough to reach the other side with OUT cutting and splicing as the instructions state. I took lose the wiring harness and there is enough wire left to reach the other side. The factory must leave make it like that to use the same harness for defferent models.
Very easy to replace. This was my second time. Hope this new dual defrost heater last longer.
Very easy to replace. This was my second time. Hope this new dual defrost heater last longer.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from New Berin, WI
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
Door closing cams on door hinges cracked and sheered off. Door sit low on hinges.
Just watch the Parts Select YouTube videos on replacing the door hinges. That helped a lot.
All I needed was a phillips head screw driver and a 5/16ths socket wrench. Easy after watching the video a few times.
All I needed was a phillips head screw driver and a 5/16ths socket wrench. Easy after watching the video a few times.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Riverton, UT
- Parts Used:
- WR51X10101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Screw drivers
freezer compartment iced up in back
removed all food from freezer compartment all shelves took four screws out removed back panel two screws from old heater unhooked the wire replaced new heater in reverse order. easy as can be
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Shawn from McKinney, TX
- Parts Used:
- WR51X10101
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
Fridge defrost Heater Bad
Followed Included instructions. My Fridge only had a single element heater; so I had to cut, strip, and relocate one of the lead wires for the heater. Overall it was a very easy fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- william from irving, TX
- Parts Used:
- WR51X10101
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Screw drivers
freezer / refrigerator to warm
removed back panel in freezer. defrosted coil, with hair drier. removed defrost heater kit. it was shot. ordered part sunday late afternoon and received the part tuesday am. great service. freezer and refrigerator worked fine after defrosting, but you want to replace the part to avoid freezing up again. to remove back panel, you remove 2 bottom guide rails 4 screws, 2 hex screws from back panel, 2 screws from defrost heater. i did have to splice wire [ provided with kit ] to reach heater.i did remove back panel twice and replace. without defrost time, even removing back panel twice, time for repair was little over an hour. at $40.00, with little down time, lots of savings, i will always deal with partselect. thanks you guys. i did the repair at 66 years of age, with no problem. you can to. one more tip. when defrosting, i placed aluminum foil under the coil and slightly up back wall. the foil was shaped to run water into a bowl in the freezer so it would not overflow the defrost pan underneath.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Thomas from Bowie, MD
- Parts Used:
- WR13X10020
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Socket set
Both Lower Door Cams Worn Through.
Part no. Ps290199 received matched part no. Ordered, which I obtained from your web site, however, part did not exactly match oem part. It was necessary to drill a new top hole in each of the hinges. New hole center was drilled 1/2" off (lower) then hole in supplied part. Jpb could have been accomplished easily by the avg. Homeowner, but the drilling required a little more skill & possible some tools that an average homeowner does not possess. Otherwise job was relatively easy and satisfactorily completed.
Was this instruction helpful to you?
Thank you for voting!