TPX24PBZCBB General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Ray from Fredericksburg, VA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Air leaking into freezer through door dispenser
I followed the video instructions. They were clear and consise. I removed the trim ring and controls. Them removed the housing and flapper. I did notice a small burr in the plastic chute and foam insulation. I trimmed this off with a utility in hopes this burr caused the flapper to warp. This is the 2nd time the flapper has been replaced in 1.5 yrs. The repair was really easy thanks to the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from Ft Myers, FL
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
air leak from ice maker flap permitting frost buildup inside ice maker dispenser
Watched à video provided at your website. Removed te cover then removed 4 screws holding the control panel' snapped out the old flap and inserted the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wanda from Katy, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
The rubber seal on the flapper came off.
My husband made the replaced the flapper while watching the video provided in your email, it was easy. Thank you.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Luis from Chester Springs, PA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper was warpped
Follow instruction on the video you provided
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from Fripp island, SC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
3rd Flap for this Ice Mkaer, keeps warping
Very Easy, follow direction I the video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from Pittsboro, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
The flapper on the freezer was warped and allowed humidity to create frost in the freezer.
I watched the how to video and followed the instructions. The entire repair took less than 4 minutes. Hardest thing was disconnecting the control panel.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- THEOTIS from CHARLOTTE, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Refrigerator COnstant running and low ice output
I followed the instructions on the youtube video on the company web page. I removed the cover by hand, removed the exisitng flapper door and install the new door, easy as pie.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CARY, NC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice maker was frosting and the dispenser chute was clogged with frost
I followed the directions on the video. Although my dispenser was a little different, I was able to get to the faulty door in less than five minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gordon from Pittsburgh, PA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper Seal for Ice Cube Chute was Warped and would not close tightly.
I followed the instructions on the video presentation, stopping the video each time until I had completed the described step. Only one minor change from the video...my refrigerator door (stainless steel) does not have the plastic edging around the control panel as shown in the video. It took me a minute or two to figure out that I had to push the tabs on the bottom of the control panel. The rest was easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brenda from Little Elm, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost buildup in the freezer near the ice chute.
I watched the video on the PartSelect.com website and decided to give it a try. The replacement of the flapper was even easier than I anticipated! The old flapper was extremely warped and was allowing air into the freezer. I'm not sure how/why it was in that condition but I am happy to report that I have no more ice buildup. Thank you, PartSelect!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jorge from Clarksburg, MD
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Ice flapper warped.
The Ice flapper was warped therefore, it was not closing well. Because of this, the ice dispenser got air in it and the ice cubes would deice causing to make a chunk of ice inside.I went on line, order the part ($5.75 + tax= $12.00) checked Part Select video and did it myself. It really is as seen on the video. It took me less than 10 minutes! I saved $200.00
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Barbara from Pasadena, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Ice/Water dispenser freezing/clogging
I followed the Video on your website and that made it so easy and simple to follow. Thank you!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Harold from Concord, CA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Frost in and around ice maker outlet
Followed the video directions. Spent about 5 minutes and I was done. Very easy to do. Problem with frost is gone. The video makes it easy to remove the plastic parts without any damage.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from Dumfries, VA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Flapper valve allowing frost/ice to accumulate in chute in summer
Followed the online video exactly and it was easily done. Couldn't have been better. The problem is solved.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cynthia from Dana Point, CA
- Parts Used:
- WR17X4152
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
I had a cracked grill on the outer part of icemaker/water dispenser
Ordered the grill and popped it in. This is the second part I have ordered from Parts Select. I previously ordered something for my microwave and the parts came very quickly too. I would highly recommend them.
Was this instruction helpful to you?
Thank you for voting!