TNX22BACBRWW General Electric Refrigerator - Instructions

Unplugged refrigerator, removed three screws to take out part, disconnected the wires and removed bad unit. Removed fan blade from old unit and attached to the new unit. Attached wires, placed the new motor back in. Plugged it back in, within 20 minutes panel between freezer and refrigerator was cool to touch.

Condensor Fan not turning. I thought it would be an easy fix. I thought I could pull off the shroud and fan assy - no joy. Too many copper pipes and lots of tubing in the way. It took 90 minutes to remove and 30 minutes to install. The BIG hint here is to loosen the shoud, pull it back as far as you can and then remove the nut that holds the fan blade in place. THEN you can remove the motor. Get the new motor back into the shroud, get the blade back on and then tighten the shroud back up.

Remove back cover, exposing fan motor. Turn off power, remove nut on fan blades. Remove fan carefully, do not bend. Unhook wiring harness. Remove three screws that hold the motor on the back frame. Remove old motor, install new. Carefully, reinstall fan blades, hook up wiring, and your ready for tryout. Also do some cleaning while your there. Clean old fan blades with hot soapy water or contact cleaner. Everything runs better clean!

First unplugged frig. Took off cover to fan, then bottom & back panels in freezer. Unplugged the fan to the wires & marked them so we would know how they went back. Unscrewed the frame that holds the fan, laid the old one next to the new one so we could tell how it went. Only took a few minutes to do this, then put it back in the same way we took it out. Plugged frig. back in & it took off. Very happy with this. Runs like a new one.

remove lower back cover - disconnect wires to fan motor - place 6" fan to blow on condenser - fridge began cooling & freezing again - ordered part - part arrived - removed fan motor & bracket - cleaned brackets & fan blade - cleaned lint & dust from condenser compartment (took longer to clean than anything else) - replaced fan motor - replaced cover - was hero with wife ... :-)

i have a friend that had a big side by side refrigerator . he had repair man after repairman come and look at it. one thought it was the overload relay in the back and another just said it was compressor problems. this went on for over a month. after all of this and no one able to fix it he went and got another refrigerator . being the tinker with stuff kind of person i am i said i will come and get the old one to keep him from having to haul it off (he agreed). well i did my home work and tried a few things messing with it. tapping on the thermistat resetting the defrost timer and it dawned on me that that the fridge would run great if i wiggle a wire on the thermistat and reset the defrost timer. so i get on the internet look around for the parts. come to find out they were realy cheap. the day they get here i break out with a screw driver and a nut driver and take the cover off. i take the old parts out and put the new ones in in about 15 minutes. i wiped the inside of the frige clean and pluged it back in. well in no time flat this thing was cooling like a northern blowing through in january. then it dawned on me that i have a 27 cubic ft frige that i didnt pay any thing for (well the 65 bucks i spent on the parts) and it runs great. what a deal.

after getting the big side by side fixed up and running like a champ i realized i have a refrigerator in the garage that my parents gave me a couple of years ago that only ran for a couple of months. well i get brave and decide to try my luck with the second one. due to it sitting up for so long and the humidity i had to do a little more work to it. i replaced a few wires, changed out a couple of connections, put a thermistat , a defrost timer and a evapmotor in it this thing also ran like a champ. i cleaned it up real good ran some steel wool over the outside and sprayed a couple of coats of enamel on it and it looks brand new.

so to end this story i spent about 140 bucks and i have two refrigerators a big side by side ice and water despensing refrigerator in the house and a 17 cubic ft refrigerator in the garage (the wife was happy simply because i had a place to put beer and bait).

if i would have went and purchased both of these refrigerators i would have spent about $1400 for the side by side and about $450 for the other one. man what a bargin, so from now on even if it seems a little dificult i dont get rid of any thing until i give it a good look over and see if i can fix it. i saved a total of $1700 (minus tax).

The fan was the correct part. It arrived one day after my well trained son-in-law had left for Texas. I had to install the motor myself. He had trained me well; it was not hard. the most difficult was getting the two tabs on the fan housing to fit back into the frame of the refrigerator where they belonged. Thanks. the part & delivery were overpriced, but I needed seed and convenience. Thanks for getting it right the first time.
John Moragues

disconnect the power to the unit. remove the retainer sctrews on the mounting bracket. remove fan motor from unit. using the rerquired tools remove the fan from the old motor and install on the new one. torque the nut until all slack is out then 1/4 turn. reinstall motor assy. and reconnect power. test the system .

I followed the directions of Steve on the installation video. He makes it easy to do the repair with his step by step description of the installation. I have repaired three different aging appliances with help of Steve and PartSelect's very helpful Customer Service.
I wish Steve a wonderful retirement and hope PartSelect can find someone as easy to follow for future videos. The videos are priceless for the repairs.

You will need a 1/4" nut driver or socket & extension.
Remove the back panel of the freezer compartment.
Pull of the wires, remove the fan assembly and replace the fan motor.

first i removed all the screws inside the freezer compartment took out theback and bottom to get to the evap motor,unpluged the wires and removed the evap motor ,removed the fan from old unit and put it on the new unit them mounted it to the back wall of the fridge,,, and put back top and bottom

Cleaned oh t freezer removed floor. Removed back inside wall removed and replaced fan and put back removed parts


L

Did not do the repair because the unit arrived damaged. The packaging was in good condition. The plastic around the plug in shattered, and some of the plastic was inside the motor. Very good, and fast on adjusting the order.

The staff at PartSelect helped me to find the correct replacement piece. The correct part arrived quickly and the price saved me some $$$. Thanks!

Part was perfect fit .Removed fan .three screws.replaced that s it