TFT30PRDBWW General Electric Refrigerator - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Wenshui from Irivne, CA
- Parts Used:
- WR51X10055
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Ice build-up in back of freezer, not cool enough
Defrost heater turned black. Test showed infinite resistance. Problem went away after the heater was replaced.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from Colleyville, TX
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
No water through door dispenser
Replaced flapper valve per website instructions. GE factory technician took two weeks to get here, charged over $100 for the call and told us we needed a new refrigerator door at a cost of over $500 to fix the problem. We sent him packing. After visiting the PartSelect website, the $5.88 PartSelect flapper valve fixed the problem. Amazing.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Anaheim, CA
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers, Wrench (Adjustable)
The icemaker quit making ice and the water started forming on the bottom of the ice bucket.
First I removed the electrical plug from the back of the freezer that plugs into the icemaker. I then removed the two hex head screws that hold the icemaker to the wall of the freezer and removed the icemaker. I removed the plastic cover, which incidentally protects the gears, by prying it off with a srewdriver. I removed three small nuts(7mm) which holds the internal cam in place. I removed the cam by pulling it off the shaft. Once I got the part from you folks I reversed the procedure that I just mentioned, and put the icemaker back together. It works great. The part with shipping was around $16.00. A new icemaker was roughly $159.00. If I would have called a technician it would have cost around $300.00 to repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ralph from Indianapolis, IN
- Parts Used:
- WR17X4153
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Grill was tarnished and flaking.
Grill for the water dispenser in the door. All I had to do was drop the new one in place.
Received the new grill in one day after ordering.
Received the new grill in one day after ordering.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Peter from HAZELHURST, WI
- Parts Used:
- 7C7
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The light bulb in my freezer door burned out.
Remove the burned out bulb and install the new light bulb.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip M. from SIMPSONVILLE, SC
- Parts Used:
- WR32X1461
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
GE vegetable drawer broken.
Concerned about removing and attaching front panel to broken drawer. Rep. said wasn't sure but most just snapped together. Rep. was correct. No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Christine from Delray Beach, FL
- Parts Used:
- WR17X10542
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
drawer facing cracked
ordered drawer face - perfect part- snapped right in. done. order came within 10 days.
will order again if needed.
will order again if needed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from BRICK, NJ
- Parts Used:
- WR17X11653
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My ice container and Ice chute were freezing up and getting blocked, and my filtered water line was also freezing
I just followed the instructions on the video and it was exactly as they said......no surprises.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmie from Surprise, AZ
- Parts Used:
- 7C7
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bulb burned out.
Screwed new bulb in socket
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from HAYMARKET, VA
- Parts Used:
- WR17X11653
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Flapper was worn and misshapen allowing warm air in freezer, ice cubes to melt and drip and impairing function of ice dispenser. Frost formed in ice dispensing chute also.
Followed the online video. Unplugged refrigerator, removed trim piece, lifted control board cover, removed 4 screws retaining circuit control board and removed the 3 connectors from the control board. Located flapper and removed by using small flat tip to take tension off flapper connectors. Helper held flash light to illuminate flapper connectors. Reversed procedure. New flapper seals well and cured problems. Circuit board was a bit different than one in video, but still had the 3 connectors. Marked each connector with grease pencil at top edge to ensure correct reconnection. Should note how wires are threaded around circuit board to ensure they are tucked back in correctly in reassembly. Remove trim piece carefully. I broke 2 of the 8 plastic pins that hold trim on. May be due to age of unit as they were brittle. 6 pins still hold trim piece flush.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Regina from Taylorsville, KY
- Parts Used:
- WR30X10093
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
icemaker quit working when we moved
My husband took out the old icemaker in about 5 minutes. The new icemaker was a perfect fit even though the refrigerator was >10yrs old. The only difficult part was the plug extension that was needed so that it would fit into an older appliance. The part was included, it just made the cord about 3 inches longer than it needed to. After working with it for about 20 minutes we were able to fit it on the back side of the icemaker. Now it works great!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Walter from SANDIA PARK, NM
- Parts Used:
- WR17X3670
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
On the water dispenser line, the heat from the compressor unit had cracked the feed line, resulting in a leak.
I removed the plate covering the water valve for the ice maker and water dispenser, removed the nut holding the 5/16" tubing to the valve and took off the tubing and nut. I did not need to turn off the water supply or unplug the unit. I removed the kick panel in the bottom front of the refrigerator, replaced the existing plastic fitting with a new push-on fitting, then spliced the tubing coming from the water chiller to the valve where the leak was thus bypassing the broken tubing with new tubing. I reassembled the valve using the original plastic compression nut, replaced the cover and ran the water dispenser while checking for leaks. The water dispanser works great with no leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Dan from HIGHLAND, MD
- Parts Used:
- WR29X5171
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
On/off switch stuck in the off position
Removed icemaker from freezer,
Removed 3 screws from cover plate, and removed screw securing main gear, removed gear.
Pulled back cover plate to expose switches and mechanism.
Removed screw holding switch to remove switch, and installed new switch.
I should have taken a pic of the cover plate, the interior mechanism and the wiring as I went along. It would have saved me 45 minutes in reassembly. Also, as luck would have it, I reversed the wiring on the switch. So off was on, and I had to remove it, switch wires and re-install.
But it works!
Removed 3 screws from cover plate, and removed screw securing main gear, removed gear.
Pulled back cover plate to expose switches and mechanism.
Removed screw holding switch to remove switch, and installed new switch.
I should have taken a pic of the cover plate, the interior mechanism and the wiring as I went along. It would have saved me 45 minutes in reassembly. Also, as luck would have it, I reversed the wiring on the switch. So off was on, and I had to remove it, switch wires and re-install.
But it works!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from PARKVILLE, MO
- Parts Used:
- WR02X10098
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
Had a 'ticking' sound
Separately (from a different site) purchased new compressor fan and motor. I purchased the grommets here because the other site listed the grommets as temporarily out of stock. I did watch one of the videos on PartSelect about the grommet replacement. Repair was pretty simple, biggest challenge was getting to the screw on the far side of the motor. Removed the two screws holding the fan motor into place. Removed motor and blade. Reinstalled with new fan blade, new grommet and new motor.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gail from LEXINGTON, SC
- Parts Used:
- WR17X11653
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Thought flapper in ice dispenser was problem. - more serious, more costly - not a DIY! New fridge here we come!
Opened, discovered not flapper but more complicated
Was this instruction helpful to you?
Thank you for voting!